Tyco DSC 3G3070-CF Instruction Manual Download Page 6

Page: 6 / 20

Installation of GS3070-CF

CONNECT 24 Enrollment Information

Only authorized dealers can enroll a 3G3070-CF with CONNECT 24. Dealer application forms and
additional information on the CONNECT 24 Voice Response Unit can be found at the CONNECT 24 web
site www

www

www.connect24.com

.connect24.com

.connect24.com. Please contact CONNECT 24 at the number below for assistance:

USA 1-888-251-7458

CANADA 1-888-955-5583

NOTE: Step 1 should be completed before powering the 3G3070-CF unit.

STEP 1 - Initialize the 3G3070-CF with Connect 24
VRU Enrolment

Call the VRU at the toll-free number: 1-866-910-3865. Follow the voice prompts and enter in your profile
number, installer ID number, installer PIN number and SIM number. Ensure all information is available
before calling the VRU. It is recommended that the radio initialization be performed at least 24 hours in
advance of installation to ensure SIM activation will be complete.

NOTE: For UL Commercial Fire listed products the supervision heartbeat shall be enabled.

WEB Enrolment

If you have credentials for www.connect24.com, you may also initialize the 3G3070 via the web. Please
check with your Connect 24 Master Reseller or Connect 24 Customer Service for more details.

STEP 2 - Determine Best Signal Location

1. Remove the screws and the front cover of the 3G3070-CF metal enclosure [1

1].

2. Fit the antenna [2

2] (ensure that the bolt [3

3] is fastened tightly).

3. Connect the antenna to the 3G Radio [5

5] and ensure the connector is secure.

NOTE: Before inserting or removing the SIM card, please ensure the unit is powered down.

NOTE: Before inserting or removing the SIM card, please ensure the unit is powered down.
4. Ensure the SIM card is placed in its socket [6

6].

5. Power up the 3G3070-CF module [4

4] and check signal strength on status LEDs [7

7].

• Use a DC power source rated 12V/0.7A connected to +/- 12V terminals [9

• Allow unit to power up
• The green LEDs will indicate the signal strength. The bottom green LED must be ON

ON for the location

to be acceptable. Please refer to the “Status LEDs” section for more information.

6. Power down the 3G3070-CF by removing the DC power source.

STEP 3 - Connect the 3G3070-CF

1. Using the cabinet, mark the 4 screw locations then drill the anchor screw holes.

NOTE: Check for cable conduits and water pipes before drilling.

2. Using anchor screws (not included), mount the cabinet to the wall.
3. Run the cables, then pull them through the cable entry or the knockouts provided.
4. Complete the connections to the terminal blocks [9

9], [11

11].

Ensur

Ensure power and T

e power and T

e power and Telco cir

elco cir

elco circuit connections

cuit connections

are made only after the cabinet has been secured to the building or structure and has been connected

are made only after the cabinet has been secured to the building or structure and has been connected
to the protective earth ground

to the protective earth ground

to the protective earth ground. Descriptions of the terminals can be found in the “Connecting the
3G3070-CF” section.
5. Using the 4 screws, reattach the front cover securely to the cabinet [1

1].

NOTE: Please refer to Figures 2 and 3 at the end of this manual for wiring diagrams.

NOTE: When installing the 3G3070-CF as a stand alone communicator in conjunction with a fire
panel that has an integrated dual telephone line dialer (dual DACT), install only one of the
telephone lines from the dual line dialer to the 3G3070-CF communicator. The second telephone
line of the dual line dialer cannot be connected to the input of the 3G3070-CF and must be
disabled in order to maintain correct functionality of the communication system. Please contact
the panel vendor for details on how to disable the second telephone line.

firealarmresources.com