TFP190
Page 3 of 4
Step 4.
Wrench-tighten the sprinkler
using only the Sprinkler Socket or
Wrench & Socket Combination (Ref.
Figure 3). The wrench recess of the
Socket is to be applied to the sprinkler
wrenching area (Ref. Figure 1A).
Step 5.
Use the Ceiling Level Tolerance
Limit indicator on the Protective Cap
to check for proper installation height.
Relocate the sprinkler fitting as neces-
sary. If desired the Protective Cap may
also be used to locate the center of the
clearance hole by gently pushing the
ceiling material against the center point
of the Cap.
Step 6.
After the ceiling has been com-
pleted with the 2 in. (50 mm) diameter
clearance hole, use the Protective Cap
Removal Tool (Ref. Figure 2) to remove
the Protective Cap and then push on
the escutcheon until its flange just
comes in contact with the ceiling. Do
not continue to push the escutcheon
such that it lifts a ceiling panel out of
its normal position. If the escutcheon
cannot be engaged with the sprinkler,
or the escutcheon cannot be engaged
sufficiently to contact the ceiling, relo-
cate the sprinkler fitting as necessary.
Care and
Maintenance
TYCO Model TY-QRF 5.6K Quick
Response, Standard Coverage, Flush
Pendent Sprinklers must be maintained
and serviced in accordance with this
section.
Before closing a fire protection system
main control valve for maintenance
work on the fire protection system that
it controls, permission to shut down the
affected fire protection system must be
obtained from the proper authorities
and all personnel who may be affected
by this action must be notified.
Absence of an Escutcheon Plate may
delay the time to sprinkler operation in
a fire situation.
Sprinklers which are found to be
leaking or exhibiting visible signs of
corrosion must be replaced.
Automatic sprinklers must never be
painted, plated, coated, or otherwise
altered after leaving the factory. Modi-
fied or over heated sprinklers must be
replaced.
Care must be exercised to avoid
damage before, during, and after instal-
lation. Sprinklers damaged by drop-
ping, striking, wrench twist/slippage,
or the like, must be replaced.
The owner is responsible for the
inspection, testing, and maintenance of
their fire protection system and devices
in compliance with this document, as
well as with the applicable standards
of the National Fire Protection Asso-
ciation (e.g., NFPA 25), in addition to
the standards of any other authorities
having jurisdiction. Contact the install-
ing contractor or product manufacturer
with any questions.
It is recommended that automatic
sprinkler systems be inspected, tested,
and maintained by a qualified Inspec-
tion Service in accordance with local
requirements and/or national codes.
Limited
Warranty
For warranty terms and conditions, visit
www.tyco-fire.com.
Ordering
Procedure
Contact your local distributor for avail-
ability. When placing an order, indicate
the full product name and part number
(P/N).
Sprinkler Assemblies
Specify: Model TY-QRF (TY3261)
5.6K Flush Pendent Sprinkler without
Escutcheon, (specify) finish, P/N
(specify):
Signal White (RAL9003). . . . . . . . . 53-261-4-162
Chrome. . . . . . . . . . . . . . . . . . . . . . 53-261-9-162
Escutcheons
Escutcheon ordered separately from
Sprinkler Assembly. See Sprinkler
Assembly for ordering information.
Specify: Escutcheon for Model TY-QRF
(TY3261) 5.6K Flush Pendent Sprinkler,
(specify) finish, P/N (specify):
75 mm Outside Diameter
Signal White (RAL9003). . . . . . . . .56-123-4-001
Chrome. . . . . . . . . . . . . . . . . . . . . .56-123-9-001
85 mm Outside Diameter
Signal White (RAL9003). . . . . . . .56-123-4-001T
Chrome. . . . . . . . . . . . . . . . . . . . .56-123-9-001T
Accessories
Socket for Model TY-QRF Flush
Pendent Sprinkler, P/N 56-000-4-947
Wrench & Socket for Model
TY-QRF Flush Pendent Sprinkler,
P/N 56-000-4-948
Protective Cap Removal Tool for Model
TY-QRF Flush Pendent Sprinkler,
P/N 56-000-4-300
ACCEPTS
3/8" SOCKET
DRIVE
WRENCH
RECESS
WRENCH
#4948
WRENCH & SOCKET
COMBINATION
#4947
SOCKET
FIGURE 3
SPRINKLER SOCKET
WRENCH & SOCKET COMBINATION
OBSOLETE
