TYAN Tomcat i7221 S5150 User Manual Download Page 67

Page: 67 / 110

Tomcat i7221 S5150

Chapter 4: SATA/RAID Setup (for SATA RAID model)

4-6

http://www.tyan.com

2. Specify a RAID Volume name and then press the <TAB> or <ENTER> key to advance to

the next field:

Intel

Choose the strip value best suited to your RAID usage model.

The following are typical values:

16KB - Best for sequential transfers.
64KB - Good general purpose strip size.
128KB - Best performance for most desktops and workstations.

Intel (R) Application Accelerator RAID Option ROM v4.0.0.6211
Copyright (C) 2003-04 Intel Corporation. All Rights Reserved.

[ ]-Change [TAB]-Next [ESC]-Previous Menu [ENTER]-Select

HELP

[ ]

CREATE VOLUME MENU

[ ]

                    Name:   RAID_Volume0
          RAID Level:   RAID0(Stripe)
                    Disks:   Select Disks
             Strip Size:  128KB
              Capacity:   68.9   GB

                                 Create Volume

3. Select the strip value for the RAID 0 or RAID 1 array by scrolling through the available

values by using the <

↑

> or <

↓

> keys and pressing the <Enter> key to select and advance

to the next field.

•

The available values range from 4KB to 128 KB in power of 2 increments. The strip value

should be chosen based on the planned drive usage. Some suggested selections are
listed below. The default selection is 128KB.

16 KB – Best for sequential transfers

64 KB – Good general purpose strip size

128 KB – Best performance for most desktops and workstations

4. Select the RAID level by scrolling through the available values by using the <

↑

> or <

↓

keys and pressing the <Enter> key to select and advance to the next field.

5. From the Strip size, press the <Tab> or <ENTER> key to advance to the ‘Create Volume’

prompt. The window will appears as follows:

Press "ENTER" to Create the specified volume.

Intel (R) Application Accelerator RAID Option ROM v4.0.0.6211
Copyright (C) 2003-04 Intel Corporation. All Rights Reserved.

[ ]-Change [TAB]-Next [ESC]-Previous Menu [ENTER]-Select

HELP

[ ]

CREATE VOLUME MENU

[ ]

║

Summary of Contents for Tomcat i7221 S5150















































































































Search results

Summary of Contents for Tomcat i7221 S5150

Reviews:

Related manuals for Tomcat i7221 S5150

Brands by name

Popular brands

TYAN Tomcat i7221 S5150, User Manual

Search results

Summary of Contents for Tomcat i7221 S5150

Reviews:

Related manuals for Tomcat i7221 S5150

Brands by name

Popular brands