TYAN Tomcat i7221 S5150 User Manual Download Page 28

Page: 28 / 110

Tomcat i7221 S5150

Chapter 2: Board Installation

2-21

http://www.tyan.com

2.11 Connecting External Devices

Your new motherboard supports a number of different interfaces for connecting peripherals.
See the diagram below. Some I/O ports may not be available with the board due to the
different configurations.

Port definitions:

PS2 mouse port (green)

PS2 keyboard port (purple)

USB 2.0 ports

Serial port (green)

VGA port (blue)

LAN1 Gigabit Ethernet port

LAN2 Gigabit Ethernet port

Peripheral devices can be plugged straight into any of these ports but software may be
required to complete the installation.

2.11.1 Onboard LAN LED Color Definition

The two onboard Ethernet ports have green and yellow LEDs to indicate LAN status. The
chart below illustrates the different LED states.

10/100/1000 Mbps LAN Link/Activity LED Scheme

Left LED

Right LED

Link Green

Off

10 Mbps

Active Blinking

Green

Off

Link Green

Green

100 Mbps

Active Blinking

Green

Link Green

Orange

1000 Mbps

Active Blinking

Green

Orange

No Link

Off

Summary of Contents for Tomcat i7221 S5150















































































































Search results

Summary of Contents for Tomcat i7221 S5150

Reviews:

Related manuals for Tomcat i7221 S5150

Brands by name

Popular brands

TYAN Tomcat i7221 S5150, User Manual

Search results

Summary of Contents for Tomcat i7221 S5150

Reviews:

Related manuals for Tomcat i7221 S5150

Brands by name

Popular brands