TYAN Tempest i5000VF S5370 User Manual Download Page 53

Page: 53 / 75

3.3.6 Console Redirection

PhoenixBIOS Setup Utility

Main

Advanced

Security Power Boot Exit

Console Redirection

Item Specific Help

Com Port Address

Baud Rate
Console Type
Flow Control
Console connection:
Continue C. R. after POST:

[Disabled]

[19.2K]
[VT100]
[None]
[Direct]
[Off]

Help

↑↓

Select Item

-/+

Change Values

Setup Defaults

Esc

Exit

←

→

Select Menu

Enter

Select

Sub-Menu

F10

Save and Exit

Com Port Address

If enabled it will use a port on the motherboard.

Disabled

/ On-board COM A / On-board COM B

Baud Rate

This feature is used to enable the specified baud rate.

19.2K

/ 300 / 1200 / 2400 / 9600 / 38.4K / 57.6K / 115.2K

Console Type

This feature is used to enable the specified console type.

VT100

/ VT100.8bit / PC-ANSI, 7bit / PC ANSI / VT100+ / VT-UTF8

Flow Control

This feature is used to enable the flow control.

None

/ XON/XOFF / CTS/RTS

Console Connection

This feature is used to indicate whether the console is connected directly to the
system or a modem is used to connect.

Direct

/ Via modem

Continue C.R. after POST

This feature is used to enable console redirection after OS has loaded.

Off

/ On

Summary of Contents for Tempest i5000VF S5370












































































Search results

Summary of Contents for Tempest i5000VF S5370

Reviews:

Related manuals for Tempest i5000VF S5370

Brands by name

Popular brands

TYAN Tempest i5000VF S5370, User Manual

Search results

Summary of Contents for Tempest i5000VF S5370

Reviews:

Related manuals for Tempest i5000VF S5370

Brands by name

Popular brands