TYAN S1682D Manual Download Page 2 | Manualshive

Page: 2 / 29

background image

2

S1682D-001-02 http://www.tyan.com

TABLE OF CONTENTS

1. Introduction.......................................................................3

1.1 Overview............................................................... 3
1.2 Hardware Specifications........................................ 4
1.3 Software Specifications......................................... 5
1.4 Environment........................................................... 5
1.5 Manual Organization ............................................. 5
1.6 Manual Conventions............................................. 6
1.7 CPU Prototypes ..................................................... 6

2. Board Installation............................................................ 8

2.1 Unpacking.............................................................. 8
2.2 Installation of the motherboard ............................ 8
2.3 S1682D Board Layout & Jumper Locations.........

9

2.4 CMOS RTC............................................................15
2.5 Installing cables and Connectors ........................

15

2.6 DRAM Installation .............................................. 17
2.7 L2 Cache Memory/SRAM Memory......................

18

2.8 VRM (Voltage Regulator Components)................

18

2.9 Peripheral Device Installation................................ 18
2.10Connecting the Power Supply...............................

18

3. CPU Installation and Removal .................................... 19

3.1 Installation of Pentium II Active Processors.........

19

3.2 Installing CPU Cooling Fans................................. 20
3.4 Installing Pentium II Passive Processors...............

21

3.4 Removal of Pentium II Passive Processors............ 21

4. Troubleshooting............................................................... 24

4.1 Troubleshooting procedures..................................

24

4.2 Technical Support procedures...............................

26

4.3 Returning merchandise for service.......................

26

Appendix: LM78 System Hardware Monitor and Intel
LANDesk® Client/Server Manager software LDCM..... 27

Declaration of Conformity.................................................. 28

BIOS - Speaker beep codes................................................. 29

«
1
2
3
4
...
»

Summary of Contents for S1682D






























Reviews:

No comments

Related manuals for S1682D

Brand: Intel Pages: 6

RHINO VAP133-ACP

Brand: Octek Pages: 66

Brand: Phytec Pages: 128

Brand: Sapphire Audio Pages: 50

Brand: Gigabyte Pages: 40

Brand: Microchip Technology Pages: 17

Brand: C&T Solution Pages: 65

Brand: austriamicrosystems Pages: 19

Brand: Ublox Pages: 25

Brand: OpenVox Pages: 29

TITAN TURBO PLUS ATX

Brand: TYAN Pages: 69

Brand: MATSONIC Pages: 39

Brand: Foxconn Pages: 111

WAFER-BW-N4-R10

Brand: IEI Technology Pages: 136

Brand: Mercury Pages: 42

Brand: Apex Digital Pages: 7

DS320PR412-421EVM

Brand: Texas Instruments Pages: 31

Brand: DFI Pages: 96

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands