TYAN D User Manual Download

Page: 39 / 67

Tiger i7320 / Tiger i7320R Chapter 3: BIOS Setup

3-11

http://www.tyan.com

Force Compliance Mode Entry:

Enable or Disable PCI-E Compliance mode by setting item to the desired value.

Enabled /

Disabled

DRAM Data Integrity Mode

If you have ECC memory modules installed, select the correct ECC mode with this setting.

Disabled / 72-bit ECC / 144-bit ECC /

Auto

ECC Error Type

When an ECC error occurs, it generates an interrupt. Select the type of interrupt to report:
NMI (Non-Maskable); SMI (System Management); SCI (System Control).

None / NMI /

SMI

/ SCI

SERR signal condition

Select ECC error conditions that SERR# be asserted.

None /

Single bit

/ Multiple bit/ Both

Memory Remap Function

Remaps the memory used by the BIOS (A0000 to FFFF - 384 k) above the 1 Mb limit. If
enabled, you cannot shadow Video and System BIOS.

Enabled

/ Disabled

3.4.2.1 Integrated Device Control Sub-Menu

USB Device 29, Function 1:

Enable or Disable this USB Device by setting item to the desired value.

Enabled

/ Disabled

USB Device 29, Function 0 & 1:

Enable or Disable these 2 USB Functions by setting item to the desired value.

Enabled

/ Disabled

USB Device 29, Function 7:

Control USB 2.0 functionality through this Setup Item.

Enabled

/ Disabled

Summary of Contents for D




































































Search results

Summary of Contents for D

Reviews:

Related manuals for D

Brands by name

Popular brands

TYAN D, User Manual

Search results

Summary of Contents for D

Reviews:

Related manuals for D

Brands by name

Popular brands