TYAN D User Manual Download

Page: 11 / 67

Tiger i7320 / Tiger i7320R Chapter 2: Board Installation

2-5

http://www.tyan.com

2.4 Motherboard Components

The diagram below shows the main motherboard components.

S5350

USB1

(COM1)

(VGA)

CPUFAN1

PW1

LAN1

BIOS

Intel

6300ESB

FDD1 J5

J22

SMSC

DME1737

64-bit 66MHz PCI-X PCIX-P1

LAN2

ATI

RAGE XL

LPT1

USB2

SMD

J21

BATT

64-bit 66MHz PCI-X PCIX-P 2 (Optional)

Intel

E7320

PW2

SO_DIMM PCIX-P3 J19(Optional)

FAN3

FAN7

JP4

J36

JP7

CPU1

FAN2

FAN1

CPU2

32-bit 33MHz (5V)PCI PCI-1 (Optional)

32-bit 33MHz (5V)PCI PCI-2 (Optional)

32-bit 33MHz (5V)PCI PCI-3 (Optional)

FAN6

JP22/27

COM2

JP16

JP21

JP24

JP32

LED1

JP8

CPUFAN2

FAN5

FAN4

JP25

JP30

JP37

JP39

JP18

JP29

JP13

JP15

JP28

JP1

Note

1. This diagram represents the latest version of the motherboard

available at the time of publishing. The board you receive may not look
exactly like the above diagram. Parts are not drawn to scale

2. PCI-1, PCI-2, PCI-3 and PCIX-P2 slots for Tiger i7320 S5350 only.
3. PCIX-P3 (SO_DIMM) socket for Tiger i7320R S5350-1U only.

Summary of Contents for D




































































Search results

Summary of Contents for D

Reviews:

Related manuals for D

Brands by name

Popular brands

TYAN D, User Manual

Search results

Summary of Contents for D

Reviews:

Related manuals for D

Brands by name

Popular brands