manualshive.com logo in svg

Twister T4, User Manual

Share
Download
Twister T4 User Manual Download Page 26

T W I S T E R T R I M M E R . C O M

If any problems not listed in this sec  on arise, or any 
troubleshoo  ng solu  ons do not solve the problem, 
contact Keirton technical support for assistance (see 

Contact Us

 on page 30).

Product is Not Exiting the T4 
Tumbler

Possible Causes:

 

• 

The T4 is not inclined enough.

 • The 

suc  on is too high.

Solution:

 

1.

 

Ensure the Trim Saver and T4 are unplugged  

 

 

and all motors have come to a complete stop.

 

2.

 Increase 

the 

T4’s 

 lt.

 

3.

 

If increasing the machine’s   lt does not solve the problem, purchase a Vacuum Bypass to   

  reduce 

suc  on (see 

Bypass

 on page 29).

Suction from the Vacuum Seems Weak

Possible Causes:

 

• 

The vacuum outlet is placed too close to a wall.

 • The 

fi

 lter bags are dirty.

 

• 

The Vacuum Bypass is allowing too much air

fl

 ow.

 

• 

The hose is blocked.

 

• 

The gasket connec  ons have leaks.

 

• 

There is buildup on the impeller.

TURN OFF ALL MOTORS, THEN 

UNPLUG THE TRIM SAVER AND 

T4 BEFORE CONDUCTING ANY 

TROUBLESHOOTING.

DANGER

!

p g   |   2 4

T R O U B L E S H O O T I N G

Summary of Contents for T4



































Reviews:

No comments

Brands by name

Popular brands

Load more brands