background image

 

 

 

 

 

INSTALLATION 

Connection of the safety heat exchanger (Quenching coil) 

(Only for boilers provided with safety heat exchanger)

 

 
The boiler has a build-in safety 
heat exchanger which cools the 
boiler in case of pump failure or 
the like. The system will be 
activated if the water 
temperature in the boiler 
exceeds 95°C. 
 
The thermal safety valve must 
be connected to constant water 
pressure from a G¾”/22mm 
pipe. The water pressure must 
be minimum 2 bar and the 
temperature maximum 15°C 
There must be no shutoff valves 
on the pipe supplying the valve.   
 
Flush the pipes before 
connecting to the thermal safety 
valve. Dirt or metal shavings 
can cause the valve to 
malfunction. 
 
The return drain from the safety heat exchanger G¾” must be connected to a 
drain. 
The pipe used to connect to the drain must have a sufficient size to avoid the 
emergence of backpressure. 
 
After installation the system must be tested to ensure free passage trough the 
safety heat exchanger. The thermal safety valve can be manually activated by 
pressing the red cap. 

 

 

Thermal safety valve - 95°C

Supply cold water for 
quenching coil

Temperature sensor
for thermal safety valve

Drain from quenching coil

Summary of Contents for M20i


















Reviews: