background image

WARRANTY – TRANSPORT BLOWERS

Subject to the terms and conditions hereinafter set forth and set forth in General Terms of Sale, Tuthill Vacuum & Blower 

Systems (the Seller) warrants products and parts of its manufacture, when shipped, and its work (including installation and 

startup) when performed, will be of good quality and will be free from defects in material and workmanship. This warranty 

applies only to Seller’s equipment, under use and service in accordance with Seller’s written instructions, recommendations 

and ratings for installation, operating, maintenance and service of products, for a period as stated in the table below. Because 

of varying conditions of installation and operation, all guarantees of performance are subject to plus or minus 5% variation. 

(Non-standard materials are subject to a plus or minus 10% variation)

PRODUCT

TYPE

WARRANTY DURATION

New

18 months from date of shipment, or 12 months after initial startup date, whichever occurs first

Remanufactured

12 months from date of shipment, or 12 months after initial startup date, whichever occurs first

Repair

12 months from date of shipment, or remaining warranty period, whichever is greater

THIS WARRANTY EXTENDS ONLY TO BUYER AND/OR ORIGINAL END USER, AND IN NO EVENT SHALL THE SELLER 

BE LIABLE FOR PROPERTY DAMAGE SUSTAINED BY A PERSON DESIGNATED BY THE LAW OF ANY JURISDICTION 

AS A THIRD PARTY BENEFICIARY OF THIS WARRANTY OR ANY OTHER WARRANTY HELD TO SURVIVE SELLER’S 

DISCLAIMER.

All accessories furnished by Seller but manufactured by others bear only that manufacturer’s standard warranty.  

All claims for defective products, parts, or work under this warranty must be made in writing immediately upon discovery and, 

in any event within one (1) year from date of shipment of the applicable item and all claims for defective work must be made 

in writing immediately upon discovery and in any event within one (1) year from date of completion thereof by Seller.  Unless 

done with prior written consent of Seller, any repairs, alterations or disassembly of Seller’s equipment shall void warranty.  

Installation and transportation costs are not included and defective items must be held for Seller’s inspection and returned to 

Seller’s Ex-works point upon request.

THERE ARE NO WARRANTIES, EXPRESSED, IMPLIED OR STATUTORY WHICH EXTEND BEYOND THE DESCRIPTION 

ON THE FACE HEREOF, INCLUDING WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND 

FITNESS OF PURPOSE.

After Buyer’s submission of a claim as provided above and its approval, Seller shall at its option either repair or replace its 

product, part, or work at the original Ex-works point of shipment, or refund an equitable portion of the purchase price.  

The products and parts sold hereunder are not warranted for operation with erosive or corrosive material or those which may 

lead to build up of material within the product supplied, nor those which are incompatible with the materials of construction. 

The Buyer shall have no claim whatsoever and no product or part shall be deemed to be defective by reason of failure to 

resist erosive or corrosive action nor for problems resulting from build-up of material within the unit nor for problems due to 

incompatibility with the materials of construction.

Any improper use, operation beyond capacity, substitution of parts not approved by Seller, or any alteration or repair by 

others in such manner as in Seller’s judgment affects the product materially and adversely shall void this warranty.  

No employee or representative of Seller other than an Officer of the Company is authorized to change this warranty in any 

way or grant any other warranty. Any such change by an Officer of the Company must be in writing.

The foregoing is Seller’s only obligation and Buyer’s only remedy for breach of warranty, and except for gross negligence, 

willful misconduct and remedies permitted under the General Terms of Sale in the sections on CONTRACT PERFORMANCE, 

INSPECTION AND ACCEPTANCE and the PATENTS Clause hereof, the foregoing is BUYER’S ONLY REMEDY 

HEREUNDER BY WAY OF BREACH OF CONTRACT, TORT OR OTHERWISE, WITHOUT REGARD TO WHETHER ANY 

DEFECT WAS DISCOVERED OR LATENT AT THE TIME OF DELIVERY OF THE PRODUCT OR WORK. In no event shall 

Buyer be entitled to incidental or consequential damages. Any action for breach of this agreement must commence within 

one (1) year after the cause of action has occurred.

January 2005

Summary of Contents for T1055



































Reviews: