Turtle Tough TT-ISE-CL2, Manual

Page: 29 / 51

TURTLE
TOUGH
®
29


s a universal switching power supply and can be connected to
ase power anywhere in the world. The power supply converts
ating voltage of 24VDC.
power input module that is pre
ield wiring to the power supply is required. The analyzer is
d with IEC #60320 C13 and NEMA
inlet to accept an IEC #60320 C13 connector.
r to disconnect the analyzer from the main power supply if
ounded
ions.
et on the analyzer and then into the wall socket.
       
   
ply with the National Electrical Code (NEC) and all local
in the same conduit.
CAUTION: the printed circuit board is sensitive to Electro
Discharge. It can be irreparably
or total operational failure. You must take the following precautions before
touching or making any connections to the circuit board:

Before touching the circuit board touch an earth grounded metal surface
such as the analyzer's power supply guard, a metal pipe or conduit to
discharge any static electricity from your body.

Wear an anti-static wrist strap connected to an earth ground.
 
chlorine analyzer us e connected to
260 Volts AC, 50/60 Hz. single upply converts
the line voltage to the analyzer's op
includes a 6 amp fuse er supply at the
factory so that no direct power input analyzer is
supplied with a 2 meter long power tors. The
power input module has an IEC mal
circuit br er supply if
15 type B al electrical
codes for international instal
Plug the power cord into t.
       
  
All electrical connections should co all local
Do not run power and signal wires
CAUTION: the printed circuit board is sensitive to Electro-Static
Discharge. It can be irreparably damaged by static electricity, causing partial
or total operational failure. You must take the following precautions before
touching or making any connections to the circuit board:
Before touching the circuit board touch an earth grounded metal surface
ch as the analyzer's power supply guard, a metal pipe or conduit to
discharge any static electricity from your body.
static wrist strap connected to an earth ground.
chlorine analyzer uses a universal switching power supply and can
260 Volts AC, 50/60 Hz. single phase power anywhere in the world. The power
wired to the p
factory so that no direct power input field wiring to the power supply is required. Th

15P c
power input module has an IEC male inlet to accept an IEC #60320 C13 connector
circuit breaker to disconnect the analyzer from the main p
socket or a grounded socket to meet l
Plug the power cord into the inlet on the analyzer and then into the wall soc
 DO NOT BYPASS THE POWER ENTRY MODULE BY CONNECTING DIRECTLY TO
THE POWER SUPPLY. DOING SO WILL VOID THE WARRANTY.
         
All electrical connections should comply with the National Electrical Code (NEC)

All electrical connections should comply with the National Electrical Code (NEC) and all local
regulations.
Do not run power and signal wires together in the same conduit.
Static
damaged by static electricity, causing partial
or total operational failure. You must take the following precautions before
Before touching the circuit board touch an earth grounded metal surface
ch as the analyzer's power supply guard, a metal pipe or conduit to
The TT-ISE-CL chlorine analyser uses a universal switching power supply and can be connected to
100-260 Volts Ac, 50/60 Hz. single phase power anywhere in the world. The power supply converts
the line voltage to the analyser's operating voltage of 24VDC.
The analyser includes a 6 amo fused power input module that is pre-wired to the power supply at the
factory so that no direct power input field wiring to the power su p ply is required. The analyser is
supplied with a 2 meter long power cord with IEC #60320 C13 and NEMA 5-15P connectors.
The power input module has an IEC male inlet to accept an IEC #60320 C13 connector.
1. Install a 15 amp circuit b r eaker to disconnect the analyser from the main power supply if
regulations require.
2. Install a NEMA 5-15 type B grounded socket or a grounded socket to meet local electrical codes
for international installations.
3. Plug the power cord into the inlet on the analyser and then into the wall socket.