background image

 

 

TROUBLE SHOOTING GUIDE

 

 

1. 

Verify  that  all  the  bolts  and  nuts  are  locked  properly  and  the  turning  parts  should  be 
turned freely without damaged parts.

 

2. 

Clean the equipment with soap and slightly damp cloth only.    Please do not use any 
solvent to clean the equipment.

 

 

 

 

 

 

 

 

Problem

 

Potential Cause

 

Corrections

 

Base is unstable.

 

 

1. 

Floor is not flat or there is 
small object under the front 
or rear stabilizer.

 

2. 

The rear stabilizer end caps 
have not been leveled 
when adjusting.

 

1. 

Remove the object.

 

 

 

2. 

Adjust the rear stabilizer end caps.

 

Handlebar is 
shaking.

 

The Bolts are loose.

 

Tighten the Bolts.

 

Loud noise from 
the moving parts.

 

The interval of the parts is 
improper tighten.

 

Open the covers to adjust.

 

No resistance 
when riding the 
bike.

 

1. 

The interval of the magnetic 
resistance increases.

 

2. 

Tension control knob is 
damaged.

 

3. 

Belt slips.

 

4. 

The bearing set is damaged.

 

1. 

Open the covers to adjust.

 

 

2. 

Change the tension control knob.

 

 

3. 

Open the covers to adjust.

 

4. 

Change the bearing set.

 

Summary of Contents for Sport-Tronic ElliptiForce X7















Reviews: