background image

D) REMOVING CLOGS (Figure 2) 

Follow these steps if the turbine becomes obstructed: 
1. Turn off vacuum system and disconnect the Powerhead. 
2. Remove the clear belt cover by turning the Powerhead over and  
rotating the two latches until they align with the openings in the belt 
cover. Remove the belt cover. 
3. Remove debris from the intake or turbine. Rotate brush to ensure the 
system is clear. Ensure the orange seal on the belt cover and mating 
surfaces are clean before reinstalling the belt cover. 
4. To reinstall the belt cover, simply insert the front of the belt cover 
under the baseplate edge and lower into its original position. 
5. Secure the belt cover in place by turning the two latches to the 
locked position. 

 

E) REMOVING THE BELT 

1. Turn Turbine powerhead over so bottom is facing up. (Place on 
folded towel to prevent scratching and rocking.) 
2. Remove Clear Belt Cover by turning both black latches counterclock-
wise until they snap into the unlocked position. Grasp the clear tab and 
lift.  
3. Use a Philips screwdriver to remove the three Base Plate screws, 
then set Base Plate aside. 
4. Lift Brush Roller from Housing Slots and then slip Poly-V Belt off 
Drive Shaft.  

Base Plate 

 

Poly-V Belt  

Drive 
Shaft 

Clear 

Belt 

Cover 

 
        

Figure 2 

Summary of Contents for Turbine Powerhead

















Reviews: