background image

7

OPERATING INSTRUCTIONS

Level and set your merchandiser in place. Connect all necessary electrical 

connections. Your Open Display Merchandiser should now be ready for use.

POWER SWITCH:

Located at the bottom of front panel, colored in red.

LIGHT SWITCH:

Located at the bottom of front panel, colored in green. 

TEMPERATURE CONTROL:

The temperature control is located underneath the bottom shelf and near
the inner right-hand side of your merchandiser.
  1. The default setting for the control is Normal. 
  2. The working temperature is from 37℉ to 40℉. 
  3. To lower the temperature, adjust the knob towards “COLD”.
      To raise the temperature, adjust the knob towards “WARM”. 
  4. In case of icing caused by hikes in ambient temperature or humidity,
      adjust the knob towards “WARM”. 

THERMOMETER:

Thermometer showing temperature is located on the right side of the back
panel under the fourth shelf. 

PRODUCT PLACEMENT:

Overloading of product or placing products against the back wall may cause
disruption in air flow, which may cause the unit to not cool properly.

NOTE:

• Do not place products into your merchandiser until the desired temperature is reached.

• Do not place hot  products into the merchandiser.

Summary of Contents for TOM-36DX














Reviews: