background image

OWNER & OPERATOR
INSTRUCTION MANUAL

For service contact:

German Knife Inc.

1-800-500-3519

www.turboairinc.com

Model No.

www.turboairinc.com

IMPORTANT SAFETY NOTICE

THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL GAS EQUIPMENT, WHO SHOULD 
PERFORM THE INITIAL FIELD START-UP AND ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL.
POST IN A PROMINENT LOCATION THE INSTRUCTIONS TO BE FOLLOWED IN THE EVENT THE SMELL OF GAS IS 
DETECTED. THIS INFORMATION CAN BE OBTAINED FROM THE LOCAL GAS SUPPLIER.

IMPORTANT

In the event a gas odor is detected, shut down units at main shutoff valve and contact the local gas company or gas supplier for service.

FOR YOUR SAFETY

Do not store or use gasoline or other flammable vapors or liquids in the vicinity of this or any other appliance.

WARNING

Improper installation, adjustment, alteration, service or maintenance can cause property damage, injury or death. Read the installation, 
operating and maintenance instructions thoroughly before installing or servicing this equipment.

TAR-6 / TAR-36G / TAR-36RB

TAR-4 / TAR-24G / TAR-24RB

TARG-2B24G / TARG-24G2B

TARG-4B12G / TARG-12G4B

TARG-6B12G / TARG-12G6B

TAR-8

TARG-2B36G / TARG-36G2B

TARG-4B24G / TARG-24G4B

TARG-8B12G / TARG-12G8B

TAR-10

TARG-6B24G / TARG-24G6B
TARG-4B36G / TARG-36G4B
TARG-2B48G / TARG-48G2B
TARG-6B24RG / TARG-24RG6B

Summary of Contents for TAR-10















Reviews: