Tuohy ANDAVI, Installation Instructions Manual, Page: 13 / 13

Receiver Specifications:
Remote Specifications:
Output Voltage: 12V DC
Max-Output Load: 5A, 60W
Dimming Range: 100% - 1 %
I nstallation Instructions
Single Zone Wireless Round Dimmer
12V DC 60W Capacity
READ ALL INSTRUCTIONS BEFORE INSTALLING SYSTEM.
Before beginning installation, be sure power is turned OFF to light system.
Programming Instructions :
Tresco Lighting
by Rev-A-Shelf
Tel: 800-227-1171
Fax: 502-491-2215
Email: cservice@trescolighting.com
Web: www.trescolighting.com
+
6.89”
25%
75%
Dimming
Z
PROGRAM BUTTON
*Under access cover
L-DC-ELT18-CON
L-DC-ELT60-CON
L-DC-ELT18-CON
L-DC-ELT60-CON
Learning Key
Dimmer Receiver
1 2 3
4
7 5
8 6
25% 50%
75% 100%
S S
Power Supply
Mounting Block
Figure 2
Figure 3
4" (101 mm)
Input Wire
Output Wire
Male AMP
®
Connector
Save these instructions for
future reference.
For technical assistance: 1-800-227-1171
Female AMP
®
Connector
4" (101 mm)
Figure
1
I-WLDIM1RND- 10 15
1. Disconnect Mounting Block from 12V DC Tresco power supply (see spec
guide for power supply options). Connect Dimmer Receiver to Tresco 12V DC
power supply by locating the input wire to the receiver and snapping the male
AMP connector to female AMP connector located on output wire of the power
supply
(Figure 2)
.
*
To use multiple receivers on one power supply, connect the input wire of the Mounting Block to the
power supply output and then plug the receivers into the Mounting Block.
2. Take the mounting case off of the Round Dimmer Controller (figure 1) .
Remove the clear plastic tab to activate the battery.
3. Plug desired light(s) into the Mounting Block.
4. Plug polarized 2-prong end of Tresco 12V DC power supply wire into 120V
receptacle. If receptacle is operated by on/off wall switch, turn switch on after
plugging power supply in.
5. Press (do not hold down) the Learning Key
(figure 3) on the Dimmer
Receiver once , then press (do not hold down) the power button on the Round
Dimmer Controller once . The lights should flash on/off, indicating they are
programmed properly.
6. Repeat step 5 with any additional receivers or controllers that you
want
programmed .
*
Each receiver can be controlled by up to 8 different controllers. A single controller can
control up to 10 receivers.
Round Dimmer Controller
How to D eprogram a R eceiver:
1. Hold down the Learning Key on the Dimmer Receiver until the lights
connected to the receiver flash on/off twice.
2. The receiver is now reset and is no longer programmed to any
controllers.
IMPORTANT SAFETY INSTRUCTIONS
CAUTION: To reduce the risk of fire, electric shock, or injury to persons:
• Route and secure cords so they will not be pinched or dam
aged when cabinet is pushed
to the wall.
• Use only insulated staples or plastic ties to secure ALL loose cords.
• 12VDC
input only to receiver
• 12VDC 60W 5AMP max receiver output
• Use only in dry locations. Not for use where exposed to the weather
• All wiring must follow NEC regulations.
Dimmer Receiver
1-1/2”
(38 mm)
5/8”
(19 mm)
Dimmer Mounting Instructions :
1. There are three options for mounting: screws ( Figure 4 ), magnet (located on
bottom of casing), or double-stick adhesive (included in package).
2 .
To mount with screws, first remove the casing from the dimmer. Position the
casing at desired location, being sure to align the "notch" on the inner wall of the
casing ( Figure 5) at the top of the cylinder to ensure proper orientation of the
control button on the Dimmer.
Figure 4
Figure 5
Alignment
Notch
Dimmer Casing
3 . Mark screw hole locations and use a 1/16" drill bit for pilot holes. Drive screws
the through holes in casing into pilot holes, again ensuring that the notch on
casing i s at the top portion of the cylinder.
4 . Slide Dimmer control unit into Dimmer casing ( Figure 6).
Figure
6
• Replace battery with CR2025 Battery only. Not rechargeable.
Operating Voltage: 3V CR2025 battery Input Voltage: 12V DC
916.5 MHz
1
1