background image

24

25

Teileabbildung •  Illustrations of parts  • Illustration des pièces 

8555.000 

Teileliste
RO Water Controller 

List of parts
RO Water Controller 

 Liste des pièces
RO Water Controller 

1

8555.100  Controller 8555 

Controller 8555 

Controller 8555 

2

8555.200  Valve 

Water valve 

Electrovanne 

3

5012.010 Netzteil 12V

Power supply unit 12V

Alimentation secteur 12V

4

3000.220  Lochschiene 

Mounting bar 

Barre de montage 

5

3155.100 

Schiebeteil 
Sicherheitssensor 

Sliding unit for sensor 

Piéce coulissante 
pour capteur 

6

3150.310  Halteplatte für Sensoren 

Holder board 

Plaque pour capteur 

7

3000.270  Klebebefestigung für Halter 

Adhesive attachment 
for holder 

Plaquettes de 
support à coller 

8

3000.240  Klemmhalter 

Clamp holder 

Attache de support 

8a 3000.243  Schraubenset 

Screw set 

Set de vis 

Die Teileabbildung zeigt die mitgelieferten Einzelteile. Die Ersatzteilliste enthält auch Teile die von den 
Teileabbildungen abweichen können. 

The illustration shows the individual parts supplied. The list of spare parts may also contain parts which 
deviate from the illustrations. 

L’illustration des pièces indique les différentes pièces utilisées. La liste de pièces détachées comporte 

aussi des pièces pouvant différer de cette illustration. 

Summary of Contents for RO Water Controller 8555
















Reviews: