background image

HD(i)-24V-GD-0111-EN 

4

 

REAR PANEL 

 
Chassis ground screw: 

The chassis ground screw must be properly connected to the chassis of your vehicle before operating 
the inverter. 

 
Fan(s): 

In order for the inverter to properly operate, the fan(s) opening must never be obstructed. Allow at 
least six inches of clearance around the inverter for airflow. All fans are thermostatics and operate 
upon the interior temperature of inverter. 

 

REMOTE CONTROL

  

 
ON/OFF: 

Your inverter is equipped with one 6 meters jack remote switch. The remote switch allows you to 
mount your inverter out of sight and turn it ON or OFF from a convenient location. The ON/OFF 
switch on the inverter’s front panel must be turned on for the remote to be operational.   

 
Input Voltage: 

By pressing the “SELECT” button until the “INPUT VOLTAGE ” light comes on, the battery voltage 
indicator displays the voltage at the input terminal of the inverter. Usually this voltage is very close to 
the battery voltage and the difference, if any, is caused by the resistance of the cables and 
connections. A regular maintenance will contribute to minimize the possible resistance (see 5).  

 
Output Power: 

By pressing the “SELECT” button until the “OUTPUT POWER” ligh comes on, the watts indicator 
displays the current provided by the inverter in KW. 1 KW = 1000 watts. If you read 1.20, it means 
the inverter is providing 1200 watts.  

 
“FAULT” light: 

An audible alarm will sound announcing a faulty condition such as: low or high battery voltage and 
overload. 

 
“OVERTEMP” light: 

An audible alarm will sound announcing an overtemp condition.  

 

“LVP” on display: 

Indicates the inverter is in Low input Voltage Protection mode (see 4.3).  

 

“OLP” on display: 

Indicates the inverter is in High input voltage Protection mode or if your consumption exceeds the 
nominal capacity of the inverter (see 4.3).  

3

 

Permanent Installation 

 
The use of the Tundra International installation kits is strongly recommended. 

These complete installation kits are custom 

designed to maximize performance. It has been developed to promote safe installation and to help eliminate the difficult task of 
sourcing  the requisite and right material. 

 

Recommended material 

HD1224

 

HD & HDI1824 

HD2524 

HDI3024 

 
-

 

Tundra CM series installation kit         

CM1000 CM1200/1500 

 

 

CM1800/2000  CM2500      

Or 
-

 

Welding  cable                                              AWG #4 

AWG #2 

AWG #1/0 

AWG #2/0       

-

 

Battery copper cable No. 8 AWG 

-

 

PVC strain relief for flexible cable                 ½”  

½” 

¾” 

¾”      

-

 

6 Tin plated terminal lugs  

 

 

 

-

 

CNL fuse block 

-

 

CNL fuse                                                         100A 

150A 

200A 

250A 

     

-

 

Plastic « loom » tubing  

-

 

Heavy duty AC power distribution center 

-

 

Red and black heat shrinkable tubing 

-

 

Plastic cable ties 

-

 

Clamps and bolts 

Summary of Contents for HD 1824














Reviews: