background image

 

 

 

5

 

 

Due to the structure of the machine hydraulics, the hydraulics should be used only when a 12V 
supply voltage is connected to the machine. If the power supply is out of order, act with extreme 
caution 
in the use of hydraulics, because the movements taking place are unlimited! 
 
Optional hydraulic row markers may move very quickly, especially if the hydraulic throttle valve is 
open and the tractor hydraulic flow is high. Use extreme caution when trying out lift and a lowering 
of markers for the first time. Make sure that nobody is under a marker or trajectory lifted up with 
hydraulics. 
 
Make sure that at least 20 per cent of the tractor's weight is left on the front axle of the tractor under 
all circumstances. If necessary, use additional weights. Be especially careful if the drill is 
connected to an interim processing device and you are raising it with the tractor's lifting gear i.e. 
in a case of reversal. 
 
The maximum speed in good conditions is at 30 km/h. Extreme caution and reduced speed must 
used on uneven surfaces. Transfers should be preferably made when containers are empty. Load 
being transported on the machine is prohibited. In order to keep tires from breaking, avoid driving 
over rocks and other obstacles.  
 
Never select a driving lane, where the extreme wheels of the machine are "on empty". In such 
condition the machine can get too much swing. Choosing a wrong driving lane, can cause the 
machine to fall. 
 
Always, use caution when moving on top of the machine for cleaning or maintenance work 
purposes, or filling the tanks.  
 
When heated, machine painted surfaces can excrete gases harmful to health. Take care of efficient 
ventilation in your workspace for example during welding operations. 
 
Use only manufacturer-approved accessories and equipment. The party carrying out alterations 
which does not follow manufacturer's instructions is responsible for the alterations and their 
consequences. 
 
The use of respiratory protective devices is recommended, especially when filling the optional seed 
dressing. Till Seed Drill does not cause any substantial increase in the noise level at the driver's 
cabin. Possible hearing protection required depends on the tractor  noise level. When handling 
heavy and sharp components (e.g. drawbar and coulter parts) the use of safety boots is 
recommended. 
 
Keep your machine up to date also on the required road equipment, in case the machine has to be 
transported on public roads. Regulatory changes are often made. 

 
 

3. MACHINE APPLICATION 
 

Tume Nova Combi –Till Seed Drill is intended for simultaneous seeding and fertilization. It is well 
suited for all sowing methods: direct sowing, sowing on minimally cultivated or on normal 
cultivated soil. 
 
The machine can also be used only for seeding or fertilization, according to the boundary 
conditions stated below. Due to its structure, Nova Combi also intensifies the soil with its support 
wheels. Under most circumstances, the support wheels also close the grooves made by the 
coulters. 
 
With the additional accessories, the number of features of Nova Combi may be increased, as the 
combination machine and accessory may do the drilling and fertilization and, during the same 
pass, among other things to modify or even out the arable land, sow grass seeds, cover the sown 

Summary of Contents for Nova 3000 Star









































Reviews: