manualshive.com logo in svg

TUFFTEC 2.0 Locker Series, Installation Instructions Manual

Share
Download
TUFFTEC 2.0 Locker Series Installation Instructions Manual Download Page 2

Table of Contents

Page 2

Solid Plastic Tufftec 2.0 Locker Installation Instructions

Thank you for purchasing our product, your business is greatly appreciated. If 
you have any questions, comments, or concerns with the product you received 
please contact the factory. Your feedback on our product and performance is 
welcome and needed in order for us to continue providing you with a quality 
product. Contact us at 800-445-5148 or fax 800-551-6993.

Section 1: Terminology
Section 2: Components
Section 3: Site Preparation
Section 4: Hardware
Section 5: Bases
Section 6: Lockers
Section 7: Fillers
Section 8: Flat Tops
Section 9: Slope Tops
Section 10: End Panels & Base Trim

Tools Needed:

• Chalk Line
• Tape Measure
• Screwdrivers (Phillips and Flat head)
• Adjustable Wrench
• Level
• Jigsaw
• Power Drill with a Drill Index, Masonry Bits, and a Countersink
• Blocking (Nailers)
• Scranton Products Provided Drawings

Please read all of the instructions prior to installing this product. If you have any 
questions contact Scranton Products as soon as possible before installing this 
product.

Summary of Contents for 2.0 Locker Series





















Reviews:

No comments

Brands by name

Popular brands

Load more brands