background image

 

©2021 Tudor Games, Inc. All Rights Reserved. Patent Pending.                                  Page  2

 

 

  

 

For “Fab Five” 11 Player Sets      

2

 

  

Uni-Forms

 Application Instructions

 

figure’s left leg and the figure’s visible waistline. POSITION the 
edge of the Film along the parting line that runs down the figure’s 
left leg. 

5.

 

Using your flattening tool, SET 

only the leg stripe edge

 of the Film 

to the figure’s left leg along the parting line. Now, both leg stripe 
edges are SET to the figure, while the rest of the Film hangs down 
below the waist. 

 

6.

 

Using your flattening tool, now SET the waistline to the figure. 
There may be some excess Film  that bunches in this area, but 
don’t be concerned, it will be partially covered by the Uni-Forms 
jersey when applied later. 

7.

 

At this point, there should be three Film “flaps” on the pants that 
are UNSET: two leg flaps and a central groin flap. The leg flaps 
will be SET first, so push the groin flap up and out of your way for 
now. 

 

8.

 

Gently SET the leg flaps to the backs of the figure’s legs with your 
flattening tool. Start at the leg stripe and work your way around 
toward the inside back of each leg, FLATTENING as you go. Do 
small sections at a time to ensure the Film is applied smoothly. 

9.

 

Now pull the groin flap up between the legs and toward the front. 
The  Film  can stretch slightly and can fill any gaps in the Film 
between the legs. Now  SET and FLATTEN the rest of the Film 
between the legs. 

10.

 

To finish the back of the pants, press your finger against the Film 
to  SET it completely and FLATTEN  out any wrinkles. Don’t be 
concerned if small wrinkles appear  when applying your Uni-
Forms. In some spots, wrinkles may be unavoidable and can 
actually add to the realism of the figure. Real uniforms fold and 
wrinkle too! 
 

Film 2: Pants Front, Right Side  

1.

 

Locate and remove Film 

from the Uni-Forms Film Sheet. 

2.

 

POSITION the edge of the Film to be applied with the right leg 
stripe edge of Film 1 that you just applied. The two Film edges 
should fit together along that parting line. If you are having 
trouble aligning the edges, you may be trying to apply the Film to 
the wrong leg, using the wrong edge, or  you’re using a Film 
Pattern from the wrong Film Sheet. 

3.

 

SET 

only the edge

 of the Film to the figure’s right leg along the 

parting line. Be sure to SET the Film’s edge well by pressing with 

your flattening tool. The two Films should fit together along the 
parting line with no major overlaps or gaps.   
 

 

4.

 

Gently stretch the Film over the right leg and adhere on the inside 
of the leg. As you stretch the Film over the leg, you should see the 
figure’s padding details start to show  through. Be gentle while 
stretching the Film to avoid rips. Don’t worry too much about the 
accuracy of the front belt line, it will be covered by the Uni-Forms 
Jersey Front when applied later. 

5.

 

To finish the Pants Front, Right Side Film Pattern, press your 
finger against the Film to SET and FLATTEN it completely. You 
can use your flattening tool or a fingernail to bring out more of the 
molded details of the leg padding underneath. 
 

 

Film 3: Pants Front, Left Side 

1.

 

Locate and remove Film 3 from the Uni-Forms Film Sheet.  

2.

 

POSITION the edge of the Film along the left leg stripe edge of 
Film 1. The two Film edges should fit together along the parting 
line.  

 

3.

 

As before, SET 

ONLY the edge of the Film

 to the figure’s left leg 

along the parting line. Be sure to SET the Film well by pressing 
with your flattening tool.  

4.

 

Gently stretch the Film over the left leg and SET and FLATTEN it 
on the inside of the leg. Be gentle while stretching the Film  to 
avoid tearing or puncturing the Film.  

5.

 

To finish the front left section of the pants, press your finger 
against the Film to SET and FLATTEN it completely. You can use 
your flattening tool or your fingernails to bring out more of the 
molded details of the leg padding underneath. 

Image 4: SET the Back of 

Pants Film on second 

anchor point 

 

Image 5: Three flaps appear after you SET both anchor points

 

Image 6: SET the edge of the 

Pants Front, Right Side Film 

 

 

Image 7: SET the edge of the Pants 

Front, Left Side Film Pattern

 

TIP:  Pressure-sensitive Uni-Forms film reacts to pressure 
by activating its  adhesive layer when  SETTING  or 
FLATTENING Films to figures. If you SET one area and 
then SET another without first FLATTENING the area 
between them, wrinkles will appear. Always SET an area 
first, then FLATTEN the remaining area toward the edge. 

Summary of Contents for Uni-Forms Fab Five

Page 1: ...g SET After POSITIONING the Film you SET it by pushing the Film down on the figure with your finger or a tool We recommend SETTING the Film in small areas and then FLATTENING the Film as you go Step by Step Instructions Please read each section completely before you POSITION SET and FLATTEN a Film Pattern While the pictures below are of the All Purpose Figure the same process is used for the Backe...

Page 2: ...g the wrong edge or you re using a Film Pattern from the wrong Film Sheet 3 SET only the edge of the Film to the figure s right leg along the parting line Be sure to SET the Film s edge well by pressing with your flattening tool The two Films should fit together along the parting line with no major overlaps or gaps 4 Gently stretch the Film over the right leg and adhere on the inside of the leg As...

Page 3: ...eg Film 6 Jersey Back 1 Locate and remove Film 6 from the Uni Forms Film Sheet 2 Center the Film behind the figure s neck The Film is cut out along the top edge to fit around the figure s neck but you may need to lift one shoulder flap up to POSITION it 3 SET the Film to the figure around the neckline then straight down the figure s back along the spine If done correctly the bottom of the Film sho...

Page 4: ...k outward from both sides around the head and down to the neck Be sure to line up the helmet stripe on Film 9 with the stripe on Film 8 if the uniform design contains a helmet stripe 4 SET and FLATTEN the rest of the helmet to the figure s head using your fingers or your flattening tool Getting the flat Uni Forms Film to adhere to the round head of the figure can be a little tricky but keep at it ...

Reviews: