2.5 SET Flash/P-T /illegal dialing prevention
When LCD displays
Press 5 to enter Flash time/P-T/ Anti-parallel
setting. Then LCD will display
1 Press “1” to enter flash time setting, LCD shows
(the default value
is 600ms),
is twinkling, press
“UP” or “DOWN”
to set the desired time. There are 8
choices: 90, 95,100,120,180,300,600 and 1000ms.
2 Press “2” to enter P-T switch mode and the LCD prompt
.
The .default setting is TONE.
is twinkling, press
“UP” or “DOWN”
to toggle from
TONE to PULSE.
3 Press “3” to enter illegal dialing prevention setting. LCD shows
,
is twinkling, then press
“UP” or “DOWN” t
o toggle from OFF to ON.
During each step, press
“FLASH/SET”
to confirm and
to exit.
2.6 SET Local area code/ Out area code
When LCD displays
Press 6 to enter local area code and out area
code setting. Then LCD will display
1. Press “1” to enter local area code setting. LCD shows
,
“
” is twinkling, Input numbers directly. There are 8 digits number can be
stored.
2. Press “2” to enter out area code setting.LCD prompts
,
is twinkling, directly to input number to activate this function while its default setting
is OFF. There are 8 digits number can be stored.
3. During each step, press
“FLASH/SET”
to confirm and
to exit.
2.7 LCD brightness adjustable
When LCD displays
Press 7 to enter LCD contrast setting. Then LCD
will display “ LCD Con 4”, “4” is twinkling, press
“UP+” or “DOWN-”
to adjust the LCD
brightness (Total 5 levels). 1 is the darkest and 5 is the brightest. The default value is 4.
Press “FLASH/SET” to save the setting and
to exit.
Remark: When LCD display becomes weaker, please change the batteries by new ones.
2.8 SET IP
When LCD displays
Press 8 to enter IP setting.
Then LCD will display
1 Press “1” to enter the auto-IP code setting,
on LCD with
blinking. Press “UP+” or “DOWN-” to choose the desired IP number and press SET to
confirm. The following numbers for selection:
IP1, IP2, 17909, 17908, 193, 17911, 17921, 17931, 17951, 17991, 068, 96300, 96333, 196,
190, 17969, 197.
2 Press “2” to enter setting the IP number manually. LCD displays
directly
input the new IP number and press
DEL
to modify, press “FLASH/SET” finally to save.
3 Press “3” to enter the second Manual IP setting, setting procedure please refer to the first
one.
Press “
FLASH/SET”
to save the setting and
to exit.
3. On-hook Operation
3.1 Reviewing the incoming calls
At On-hook status or off-hook status, press
“UP+” or “DOWN-”
to review all the incoming
call numbers, press “#” key for 3 seconds also can go into the incoming inquiry state.
3.2 Call back
When viewing incoming or outgoing calls, find the desired number, press
“BACK/÷
” to call
back directly. Holding “
BACK/÷
” key for 3 seconds phone will auto-add 0 before the number
you want to call back.
3.3 Reviewing the outgoing calls
At On-hook status or off-hook status, press “
CHECK/×
” to review the outgoing calls, using
“UP+” or “DOWN-” to backward or upward review the number, date and time of outgoing
calls.When on-hook state, pressing “*” for 3 seconds also can go into the outgoing inquiry
state.
3.4 Pre-dialing function
At on-hook state, you can input the calling number directly (edit the mistake with the
DEL
key), then press
BACK/÷
or
key to dial out.
3.5 DEL function
During the setting model, using
DEL
key to exit. In pre-dialing, use
DEL
key to delete the
wrong numbers. During the review of incoming, outgoing & stored numbers, use DEL key to
delete the certain number. If hold
DEL
key for 3 seconds, all the incoming & outgoing calls
will be deleted.
BIG 300 User manual 11x15_8giu.indd 6-7
13/06/12 11.26
