TTLIFE JY-105 Operation Instructions Manual Download Page 2

1

Key Points

Special warning:
In order to prevent power failure or oxygen generator
failure, persons in urgent need of oxygen and Critically Ill
Patient shall be provided

I.

Before Installation

Keep oxygen generator upright! Inclined angle is not more than 5 degree.

If power supply voltage is not stable, exceeding the specified voltage, please
use voltage regulator (1000W)! (Unstable p

ower supply voltage normally occurs in

the countryside

)

Please select safe and qualified socket and terminal block! (1100W better)

Unprofessional person must not open the case!

II.

Placement

Oxygen generator shall be placed in a well-ventilated place and avoid direct
sunshine, at least 10cm away from the wall and other objects.

Oxygen generator shall not place in the following environment: near heat source,
open fire and potential fire, wet, no shelter, temperature too high (≥55

), too low

(≤-20

).

Never put any heavy object,

sundries or container with water or oil

on the oxygen

generator.

Never put sundries at the bottom of oxygen generator to avoid inlet and outlet
from being blocked resulting in stoppage or oxygen concentration decrease
because the temperature is too high.

III

.

In use

Oxygen is inflammable, No smoking and far away from open fire and potential
fire to avoid fire accident.

Do not start oxygen generator frequently. Restart it in at least 30 seconds after it
shuts down.

Do not apply oil or grease on any part of oxygen generator to avoid oxygen from
being polluted or avoid fire accident.

Summary of Contents for JY-105

















Reviews: