TTControl Vision 312 User Manual Download Page 41

Page: 41 / 45

10. CONNECTORS AND CABLE SPECIFICATIONS

10.2 Receptacle contacts

TTControl recommends the following receptacle contacts for mating connectors:

Connector

Description

Note

Part no.

Supplier

For stranded wire with 0.50 mm

cross sectional area [AWG20]

3-1447221-4

TE Connectivity

For stranded wire with 0.75 mm

to 1.25 mm

cross sectional area

[AWG18 –16]

3-1447221-3

TE Connectivity

Note 1

Superseal 1.0 mm socket crimp contact.

10.3 Cavity plugs and blind plugs

TTControl recommends:

Connector

Description

Part no.

Supplier

Cavity plugs for unconnected pins

4-1437284-3

TE Connectivity

A, B, C, D

Blind plug for the connector

D4Z023-002Z

Rosenberger

NOTE

Connectors and/or cavity and blind plugs must be installed to ensure that the device is water tight.

10.4 Tools

Connector

Description

Note

Part no.

Supplier

CERTI-CRIMP

straight

action

hand tool with fixed dies

1454509-1

TE Connectivity

A, B, C, D

Repair Tool Kit RosenbergerHSD

D4W006-SET

Rosenberger

Note 1

TTControl recommends the instruction sheet 411-78017 from TE Connectivity.

Note 2

TTControl recommends ordering the cable harnesses for connectors A, B, C, and D
from a professional cable harness manufacturer.

Document Number:

D-156-G-02-001

Summary of Contents for Vision 312














































Search results

Summary of Contents for Vision 312

Reviews:

Related manuals for Vision 312

Brands by name

Popular brands

TTControl Vision 312, User Manual

Search results

Summary of Contents for Vision 312

Reviews:

Related manuals for Vision 312

Brands by name

Popular brands