TSUJI ELECTRONICS PM16C-16HW2 User Manual Download Page 35

Page: 35 / 75

6 Operation of Motor

Here, you will move the motor actually.

Prior to actually drive, complete the following settings.

･

Connecting to an external device driver, limit switches, etc. (Page 8)

･

Configuring the driving speed. (Page 24)

･

Configuring the amount of movement (only the absolute value and relative value movement)

(Page 14)

Operate the motor, after the setup is complete.

6-1 Local mode operation

1: Display the channel of the motor moving on LCD.

If it does not appear, try changing the channel using the CH SEL switch.

2: Press the A ~ D button that corresponds to move the motor, and light the LED on upper

side of button.

Motor that is indicated by LED, will move when you operate the JOG switch or press
green START button.

3: Press the MODE button, and choose how to move from four types of REL, ABS, SCAN,

and HP.

The moving method that is showed by lit, is currently selected.

4: Start the motor moving, when the START button is pressed.

(REL)

Move relative movement amount that has been set.

(ABS)

Move for absolute point amount that has been set.

(SCAN)

Green lamp at start button keep blighting, and start moving for the direction
of jog switch you pushed.

(HP)

See 4-5 Home Position Set and Search drive (Page 17) in detail.

5: Motor stops moving if you press the STOP button or limit switch is activated or etc.

6-2 Remote/Local switching command

On REMOTE mode, you can choose the motor for driving by commands.
Commands for motor move and setting are ignored at LOCAL mode.

Command REM

LOC

Select REMOTE control mode or LOCAL control mode.

Reply Nothing

Remarks It is valid only when all motor is stopped.

Summary of Contents for PM16C-16HW2












































































Search results

Summary of Contents for PM16C-16HW2

Reviews:

Related manuals for PM16C-16HW2

Brands by name

Popular brands

TSUJI ELECTRONICS PM16C-16HW2, User Manual

Search results

Summary of Contents for PM16C-16HW2

Reviews:

Related manuals for PM16C-16HW2

Brands by name

Popular brands