background image

3.SETUP mode

You can setup Encorder Counter in SETUP mode.
*When SETUP mode, Encorder Counter stops counting.

1) Setting Preparation and Completion

Turn on the Power ON SW, and you can use Encorder Couneter in a few seconds.
Setting values(MULT-P, DIR, Z-LED, ENCTYPE, LANCTRL, LAN IP:1, LAN IP2, Port no) are 
kept by battery backup.

a)

Push SETUP SW (then SETUP SW is lighted.)
LCD indicator display Setting Item.

degit→

1

2

3

4

5

6

7

8

1

2

3

4

5

6

7

8

+

0

1

2

3

4

5

6

→ M

U

L

T

-

P

+

0

0

1

2

3

4

5

1

NORMAL mode

SETUP mode

You can change setting by using (+)/(-) button under the LCD indicator.
Appearance of Cursor depends on setting item. 
When Cursor appears, You can change the position by using (←)/(→) button. 
You can change setting item by using PRESET SW.
See the order of setting items below.

MULT-P → DIR → Z-LED → ENCTYPE → TERMINTR → 
LAN IP:1 → LAN IP:2 → Port no → MAC

Setting items from LAN IP:1 to MAC are common for each channel.
So they are displayed only in A cannel LCD indicator. (MAC is Read-Only.)

b)

Push SETUP SW again, then all LCD return to NORMAL mode.
Encorder Counter starts runnig in a new setting, except for "LAN IP:1", "LAN IP:2" and
"Port no". If you change those setting value, turn off POWER ON SW after the display
returns to NORMAL mode, and trun on POWER ON SW again.

See the explanation of each setting item below.

2) MULT-P 

You can select count rate from 1,2,4 times of encoder input pulse by using (+)/(-) button.

3) DIR

You can change the relation between the direction of rotation(CW/CCW) and
count up/down direction(U:up/D:down).

4) Z-LED

You can select ENABLE/DISABLE by using (+)/(-) button.

5) ENCTYPE

You can select encorder type(L.D:Line Driber or O.C:Open Collector) by using (+)/(-) button.

6) Terminator

You can select ENABLE/DISABLE by using (+)/(-) button.

7) LAN IP:1(upper 2byte of IP address)

You can chanse IP address by using (+)/(-) button and (←)/(→) button.
Setting value is decimal number only. Default value is "192.168."

8) LAN IP:2(lower 2byte of IP address)

You can change IP address by using (+)/(-) button and (←)/(→) button.
Setting value is decimal number only. Default value is ".1.55"

9) Port no

You can set Port Number by usint (+)/(-) button and (←)/(→) button.
Setting value is decimal number only. Default value is "07777".

10) MAC

You can see MAC address , but cannot change the address.

4

Summary of Contents for ER2C-04











Reviews: