Safety
Warnings
:
The Bloom Boost is a passively
cooled system with no moving
components. Do not try to open
or disassemble the fixture, it
contains no serviceable parts
inside. Doing so may cause harm
to the fixture and void warranty.
03
04
• Always adhere to the local rules and
regulations when installing or using the fixture.
• Wearing protective gloves and glasses is
recommended during installation.
• Always disconnect from power source before
performing any maintenance to the fixture.
• The fixture will get hot during operation. Do
not touch while the light is on. Keep this
product away from children.
• Always allow at least 10 minutes for the
fixture to cool down before handling.
• Do not touch the LED diodes.
• Keep the power cord away from hot
surfaces.
• Do not plug this system into a supply
voltage other than what is instructed on
the fixture.
• Do not use the fixture when the power
cord is damaged.
• Do not use the fixtures if the unit has
been dropped, and there is damage to the
enclosure or bars.
WARNING
Risk of electrical shock.
To reduce the possibility
of serious injury, always
take the proper precautions
and unplug the fixture
before moving or cleaning.
CAUTION
To reduce the risk of
overheating or fire, never
place operating fixtures
face down on a flush
surface. Always allow for
adequate ventilation of
fixtures and power supplies.
CAUTION – RISK OF PERSONAL INJURY
Disconnect power before servicing or installing fixture. Lighted fixture
may be hot. To reduce risk of injury, turn off or disconnect power and
allow to cool before handling. Fixture must be grounded in accordance
with appropriate codes. Failure to do so may result in serious injury or
death. Be sure all power is off prior to installing fixture.
CAUTION
LED and heat sink surfaces
may be hot. Allow sufficient
cooling time before handling.
CAUTION
To prevent eye damage,
avoid looking directly at the
unshielded LEDs.
WARNING
Light bars and power supply are
splash-proof but not waterproof. In the
event that the light bar becomes
submersed, first disengage the circuit
breaker, then unplug the fixture before
proceeding to remove from water.
Safety
Warnings
:
The Bloom Boost is a passively
cooled system with no moving
components. Do not try to open
or disassemble the fixture, it
contains no serviceable parts
inside. Doing so may cause harm
to the fixture and void warranty.
03
04
• Always adhere to the local rules and
regulations when installing or using the fixture.
• Wearing protective gloves and glasses is
recommended during installation.
• Always disconnect from power source before
performing any maintenance to the fixture.
• The fixture will get hot during operation. Do
not touch while the light is on. Keep this
product away from children.
• Always allow at least 10 minutes for the
fixture to cool down before handling.
• Do not touch the LED diodes.
• Keep the power cord away from hot
surfaces.
• Do not plug this system into a supply
voltage other than what is instructed on
the fixture.
• Do not use the fixture when the power
cord is damaged.
• Do not use the fixtures if the unit has
been dropped, and there is damage to the
enclosure or bars.
WARNING
Risk of electrical shock.
To reduce the possibility
of serious injury, always
take the proper precautions
and unplug the fixture
before moving or cleaning.
CAUTION
To reduce the risk of
overheating or fire, never
place operating fixtures
face down on a flush
surface. Always allow for
adequate ventilation of
fixtures and power supplies.
CAUTION – RISK OF PERSONAL INJURY
Disconnect power before servicing or installing fixture. Lighted fixture
may be hot. To reduce risk of injury, turn off or disconnect power and
allow to cool before handling. Fixture must be grounded in accordance
with appropriate codes. Failure to do so may result in serious injury or
death. Be sure all power is off prior to installing fixture.
CAUTION
LED and heat sink surfaces
may be hot. Allow sufficient
cooling time before handling.
CAUTION
To prevent eye damage,
avoid looking directly at the
unshielded LEDs.
WARNING
Light bars and power supply are
splash-proof but not waterproof. In the
event that the light bar becomes
submersed, first disengage the circuit
breaker, then unplug the fixture before
proceeding to remove from water.
