Tryton THP1800, Instruction Manual

Page: 5 / 56

5
e) Power tools require maintenance. Check power tools for exposed metal parts of the tool “live” and shock the operator.
concentricity or jamming of moving parts, any cracks and all
f) When ripping always use a rip fence or straight edge guide.
other factors affecting the power tool work safety. If any
This improves the accuracy of cut and reduces the chance for blade
damage to the power tool is detected, it should be repaired binding.
before use. Improper power tool maintenance is a reason for many
g) Always use blades with correct size and shape (diamond vs.
accidents.
round) arbor holes. Blades that do not match the mounting
f) Cutting tools should be sharp and clean. Keeping sharp cutting hardware of the saw will run eccentrically, causing loss of control.
edges in good condition reduces the risk of jamming and facilitates
h) Never use damaged or incorrect blade washers or bolts. The
operation.
blade washers and bolt were specially designed for the specific saw, for
optimum performance and safety of operation.
g) Power tools, equipment, working tools etc. should be used
according to this user's manual taking into account
Causes and prevention of kickback:
operating conditions and the work to be done. Misusing a
- kickback is a sudden reaction to a pinched, bound, or misaligned saw
power tool can result in dangerous situations.
blade, causing an uncontrolled saw to lift up and out of the workpiece
h) At low temperatures and after a long brakes in operation it is
toward the operator;
recommended to turn the power tool to operate it with no
- when the blade is pinched or bound tightly by the kerf closing down,
load for a few minutes to provide proper grease distribution
the blade stalls and the motor reaction drives the unit rapidly back
inside its driving mechanism.
toward the operator;
i) Use soft, damp (cannot be wet) cloth and soap to clean power
- if the blade becomes twisted or misaligned in the workpiece, the
tools. Do not use petrol, solvents and other agents that may
teeth at the back edge of the blade can dig into the top surface of the
damage your equipment .
wood, causing the blade to climb out of the kerf and jump back toward
the operator.
j) Power tools can be stored/carried after making sure that all
moving components are locked and protected against
Kickback is the result of improper use of the saw or incorrect
release with original devices intended for this purpose. operating procedures or conditions and can be avoided by
taking proper precautions, as listed below.
k) Store power tools in a dry, dust and water-protected place.
a) Maintain a firm grip with both hands on the saw and position
l) Carry your power tool in its original packaging to provide
your arms to allow you to resist the kickback force. Stand on
protection against mechanical damage.
one side of the saw so as to be away from the cutting line of
WARNING! General warnings regarding the use of
the saw. Kickback may cause the saw to jump backward, but the
power tools.
kickback force can be controlled by the operator if proper precautions
Repair :
have been observed.
b) When blade is binding, or when interrupting a cut for any
reason, release the trigger and hold the saw motionless in
the material until the blade comes to a complete stop. Never
attempt to remove the saw from the workpiece or pull the
saw backward while the blade is in motion or kickback may
occur.
Investigate and take corrective actions to eliminate the cause of
blade binding.
c) When restarting a saw in the workpiece, center the saw
blade in the kerf and check that saw teeth are not engaged
into the material.
If the blade is binding, it may walk up or kickback
a) Keep your hands away from the cutting area and the blade.
from the workpiece when the saw is restarted.
Keep your second hand on the ancillary handle or on the
d) Support large panels to minimize the risk of blade pinching
motor housing. If both hands are holding the saw, they cannot be cut
and kickback. Large panels tend to sag under their own by the blade.
weight. Supports must be placed under the panel on both sides, near
b) Do not reach underneath the workpiece. The guard cannot
the line of cut and near the edge of the panel.
protect you from the blade underneath the workpiece.
e) Do not use dull or damaged blades. Unsharpened or improperly
c) Set the cutting depth to match the thickness of the item to be
set blades produce a narrow kerf causing excessive friction, blade
cut. The saw blade should extend below the workpiece by no more
binding and kickback.
than the height of the tooth.
f) Blade depth and bevel adjusting locking levers must be tight
d) Never hold the item being cut in your hands or across your
and secure before making a cut. If blade adjustment shifts while
leg. Fix the item to a stable base. Stable fixing of the item being
cutting, it may cause binding and kickback.
cut is necessary to minimize body exposure, blade binding, or loss of
control.
g) Use extra caution when making a “pocket cut” into existing
walls or other blind areas.
The protruding blade may cut objects
e) Hold the saw by the insulated gripping surfaces when
that can cause kickback.
performing an operation where the saw may contact hidden
live wiring or its own cord.
Contact with a “live” wire will also make h) Before each cut, check if the lower guard is positioned
a) Power tools can be repaired by competent persons only who
use original spare parts.
It will provide safe operation for the power
tool.
b) If a fixed power cord is damaged, to avoid risks it should be
replaced by power tool manufacturer or in a specialty repair
shop or by a qualified person.
WARNING! Circular saw – safety warnings
Personal safety: