5
operation; use protective gloves when changing the drill bit).
- Throwing back machined object or its fragment.
- Bending/breaking the drill.
The set includes:
ź
drill - 1 piece
ź
Auxiliary handle - 1 piece
ź
Depth stop - 1 piece
ź
ź
User's manual - 1 piece
ź
Warranty card - 1 piece
operators from exposure to vibrations, such as maintenance of the
electric tool and work tools, assurance of proper hand temperature, or
determination of the sequence of work operations.
n
,B,C
The vibration level value given refers to basic application of the tool. If the
tool is used for other applications or with other tools, or if it is not
maintained properly, the vibration level may differ from the values
given. The above-mentioned causes may lead to higher exposure to
vibrations during the whole work time.
One must implement additional safety measures to protect the
BEFORE YOU START:
I
mpact
1. Make sure that power supply parameters meet the requirements
provided on the drill nameplate.
2. Make sure the drill switch is in off position and switch lock (
4
) is
Carrying case - 1 piece
released. Do not put the device aside when the lock is on. To release
the lock press the switch (
6
) again.
3. The auxiliary handle (
9
) can be installed by inserting the handle
clamping ring onto the chuck and locking it by tightening the handle.
n
Device components
(see Fig.
A
)
:
The depth stop (
10
) can be installed by inserting it into the hole of the
The numbering of device components refers to graphics presented on page
auxiliary handle and tightening the auxiliary handle to lock it.
2 of the user's manual:
4. When using an extension cord make sure its parameters and cable
1.
Keyless
drill chuck
cross-section meet the drill power requirements. Extension cords
2.
Operation mode switch
drill / impact drill
should be as short as possible. When in use extension cords must be
3.
Rotation direction switch
fully uncoiled.
4.
Switch lock
5.
Rotational speed control
OPERATION:
6.
Switch
n
Selecting a drill bit
7.
Main handle
When drilling in concrete, bricks, stone masonry bits must be used. When
8.
Speed selector
drilling holes in metal, plastics, wood (hole diameters up to 6mm) use
9.
Auxiliary handle
metal bits.
10.
Depth stop
When drilling holes with a diameter exceeding 6 mm in wood, use wood
drill bits.
SPECIFICATIONS:
n
Fixing a drill bit
Insert a drill bit into the loosened chuck
(
1
)
and fix it by tightening the
outer ring holding the chuck body
(see Fig.:
B
)
.
n
Setting the drilling depth
The depth stop (
10
) can be used to set drilling depth.
Extend the drill stop to set the distance between depth stop tip and drill
bit tip that equals to the drilling depth required.
n
Selecting an operation mode
ź
Drilling and tightening/undoing screws:
Set the operation mode switch (
2
) to position «drill» marked with
symbol -
.
ź
I
mpact drilling:
Set the operation mode switch (
2
) to position «impact drill» marked with
symbol -
.
NOTE:
Never change the operation mode when the drill chuck (
1
) rotates.
n
Changing the rotation direction
Move the rotation direction lever (
3
) to a selected position until you feel
resistance. Symbols on the housing near the switch:
R
- clockwise
rotation,
L
- counterclockwise rotation.
NOTE:
Never change the rotation direction when the drill chuck (
1
) rotates.
n
Selecting a speed
By using the speed selector (
8
) users can pre-set one of the two torque
ranges:
Speed 1
: Low speed range suitable for drilling high
diameter holes or for tightening
/
undoing screws/bolts.
Speed 2
: High speed range - suitable for drilling low
diameter holes.
Frequency
50 Hz
Power consumption
No load speed
Voltage
230 V
13 mm
Drill chuck (key
less
)
Maximum hole diameter
steel
concrete
wood
- 1
0
mm
-
13
mm
-
32
mm
Sound pressure level (LpA)
Sound power level (LwA)
Vibration level according to valid standard
EN 60745-2-1/A11:07
No impact drilling
main handle
a
hD
(metal),
I
mpact drilling
(concrete) a
hID
2
t
olerance of measurements
K=1,5 m/s
92,6 dB(A)
1
0
3,6 dB(A)
2
1
5,859 m/s
2
5,562 m/s
Equipment Class
Ingress protection
Weight (with no accessories)
4,0 kg
IP20
II
MODEL
TDW1200K
1200 W
0-
1
100 rpm
Speed
1
Speed
2
0-
28
00 rpm
II
I
II
I
Summary of Contents for TDW1200K
