manualshive.com logo in svg

Trust AP115W, Manual, Page: 15 / 16

Share
Download
Trust AP115W Manual Download Page 15

 TRUST AP115W WIRELESS NETWORK KIT

15

U K

Problem

Cause

Possible solution

Windows does not
detect a new device
after connecting
the Access Point.

Old drivers are still
installed.

See chapter 3 for
instructions on how to
uninstall the Access Point.

The cable has not been
connected or has not
been connected
correctly.

Check whether light E (figure
2) is lit.

No stations or printers
have been shared with
other computers in the
network.

Share at least 1 station or 1
printer to make the computer
visible in the network.

The network card has
not logged onto the
network correctly.

Wait approximately 20
seconds and try again.

The other computers
are not visible on the
network.

The PC workgroup
name is not the same
as the workgroup name
for the other computers
in the network.

Change the workgroup in the
‘Network properties’.

The network cable has
not been connected or
has not been connected
correctly.

Connect the cable correctly
or, if necessary, replace it.

The PC-Card is faulty.

Return the PC-Card to your
dealer.

The latest FAQ’s are
available on the
Internet.

See www.trust.com/12844 for
FAQ’s and other product
information.

The problem is not
listed here.

There is another
network problem.

See the Troubleshooter:
www.trust.com> Customer
Care > Troubleshooters >
Network.

Summary of Contents for AP115W

















Reviews:

No comments