background image

24

•  Fasten the cover plate to the appliance (see Fig. 23):

 

– Position the cover plate.

 

– Screw the cover plate only loosely. Start with screw 1.

 

– Align the cover plate.

 

– Evenly tighten all 8 screws.

8 x

Cover plate 

1

Fig. 23

Top 

1

3

2

Fig. 24

•   

 

Damage to the appliance and the 

connections! 

 

– Make sure that no gas lines, water hoses or electrical 

lines are kinked or pinched. 

 

– When establishing the water connections, observe the 

installation instructions and torques specified by the 

manufacturer.

•   Connect the hose for cold water (1) at the bottom of the 

appliance.

•  Connect the hose for hot water (2) at the top of the 

appliance.

• 

AquaGo comfort plus only: 

Connect the hose for the circulation line (3).

•   Check all connections for water leaks.

 

– Repair leaks as needed. 

 

– Repeat check for water leaks and take any necessary 

steps to repair the leaks at all water connections.

•   Connect the electrical lines with the proper polarity to the 

12 VDC power supply . Refer to “Electrical connection for 

all models” on Page 22. Install a 7.5 A fuse exclusively 

dedicated to the appliance (see Fig. 19).

Top 

+ red

– black

12 V DC

Fig. 25

Gas connection

Risk of explosion or poisoning due to improper 

installation! 

•  Permit only a certified service technician to perform 

installation. 

•  The gas system must accord with the technical and ad-

ministrative provisions of the individual country of use 

(in Australia, AS/NZS 5601.2 – LP Gas installations). 

•  Make sure that the manual shut-off valve in the gas line of 

the appliance is closed.

•  Make sure that the gas line is centred and tension-free 

when it enters the grommet so that the gas line will not 

abrade the grommet. 

•  Make sure that the gas line has an SAE 45° Flare Female 

connector. 

Additional rules for the appliance gas connector.

•  For gas pipe sizing refer to AS/NZS 5601.2 

– LP Gas installations.

•  Make sure that the gas line is free of dirt, chips, etc.

•  Never use pipe dope on a flare fitting. The flare fitting is a 

dry seal.

 Connecting the gas line (gas side connection)

•  Mounting the control panel cable

 

– Feed the control panel cable (approx. 25 cm) from outside 

through the gas pipe grommet (side).

 

– Attach the control panel cable to the control unit.

 

– Hook the control panel cable on to the clip.

•  Guide the prepared gas line through the gas pipe grommet 

(side).

•  Screw the gas line’s union nut (wrench size 19 mm) onto 

the appliance’s gas connection so it is finger-tight.

Clip

Connector

Control panel cable

LP gas supply

Gas pipe grommet

Fig. 26

• 

 

Gas valve may be damaged during tight-

ening! 

Use a second wrench to counterhold at the square 

end (wrench size 19 mm). 

•   Use a torque wrench to tighten the union nut (nominal 

torque 20 Nm). 

Summary of Contents for AquaGo AU





































Reviews: