![background image](http://html1.mh-extra.com/html/true/tui-15-l-op-d-dsk-103-h08/tui-15-l-op-d-dsk-103-h08_install-manual-and-user-manual_1174727020.webp)
TRUE RESIDENTIAL
®
TEC_TM_155 REV. A
12/07/2021
Page 20 of 64
P R I O R T O I N S T A L L A T I O N
CUS TOM PANEL INS TALL ATION
Your new ice machine comes with articulating, or soft-
closing, hinges. The hinges can be installed on either
the left of right to change the direction the door opens.
Before installing panels, be sure the door assembly is
oriented as desired. See “Reversing Door” (page 56).
Please closely read all instructions before installing
your panels.
REQUIRED TOOLS
Required tools include (but may not be limited to) the
following.
• Surface protection*
• 2+ Clamps ≥ 2” (51 mm)
• 1/8” Hex Head Allen Wrench
• Phillips Screwdriver or Bit Driver
• 1/8” Drill Bit
• (Qty 6) #6 x 1/2” Screws**
• Drill
*Cardboard, moving blanket, foam padding, etc.
**Screw type varies by panel material.
INSTALL ATION
1. Carefully lay the door overlay panel face down on a
protected surface.
2. With a 1/8” hex head Allen wrench, loosen the
cabinet hinge bolts. Then, remove the door.
See fig.1.
NOTE: DO NOT REMOVE THE HINGE FROM THE
DOOR ASSEMBLY.
3. If NSF Cover is present, carefully pry screw caps
from the cover to access the door bracket screws.
See fig. 2.
NOTE: THE CAPS ARE INSTALLED WITH A
TACKY GLUE THAT CAN BE EASILY REMOVED
AND REINSTALLED.
4. Place the door front face down on the overlay
panel. Then, align the bottom door bracket’s
bottom edge with the overlay panel’s bottom edge.
See figs. 3 and 4.
5. Clamp the door assembly panel.
NOTE: IF THE CLAMP JAWS ARE NOT PADDED,
INSERT PADDING BETWEEN THE CLAMP AND
THE OVERLAY TO PROTECT THE PANEL’S
FINISH.
6. If desired, install a handle before proceeding to the
next step. For best installation, fasten the handle
with recessed screws.
7. With a 1/8” drill bit, carefully drill pilot holes into
the door front. See fig. 5.
NOTE: TAKE CARE TO NOT DRILL THROUGH THE
FRONT OF THE PANEL.
8. With the appropriate hardware, fasten the overlay
panel to the door front. Then, remove the clamps.
9. Install the door assembly. Be sure to fully tighten
the hinge screws.
10. Verify the door closes correctly and seals without
gaps. Adjust the door as needed; see “Door
Adjustment” (page 59).
Summary of Contents for TUI-15-L-OP-D-DSK-103-H08
