background image

SAFETY INFORMATION

Safety Precautions  

1

Proper Disposal, Connecting Electricity, & Adapter Plugs  

2

INSTALLATION

Ownership, Uncrating, & How to Connect to Electricity  

3

Wire Gauge Chart  

4

Locating and Leveling  

5

Installation of Legs or Castors  

6

SETUP

Standard Accessories  

7

OPERATION

Startup  

8

Mechanical Temperature Controls Sequence of Operation   9

MAINTENANCE, CARE, CLEANING

Cleaning Condenser Coil  

13

Important Warranty Information  

14

Stainless Steel Equipment Care and Cleaning  

15

WARRANTY

Warranty  

16

trcb

 – 

chef

 

base

 

equipment

TRUE MANUFACTURING CO., INC.

2001 East Terra Lane • O’Fallon, Missouri 63366-4434

(636)-240-2400 • FAX (636)-272-2408 • INT'L FAX (636)272-7546 • (800)-325-6152

Parts Department (800)-424-TRUE • Parts Department FAX# (636)-272-9471

Web: www.truemfg.com

CONGRATULATIONS! 

You have just purchased the finest commercial refrigerator 

available.  You can expect many years of trouble-free operation.

TRUE

manufacturing

 

co

., 

inc

.

INSTALLATION MANUAL

INSTALLATION MANUAL

trcb

 

models

 – 

chef

 

base

 

equipment

TABLE OF CONTENTS

TRCB-82

TRCB-52

Summary of Contents for TRCB-52


















Reviews: