background image

11052019

16

STEP 10: Locate the shooting rest rails and the shooting rest. Assemble the three (3) components as shown in Figure 25 using two 

(2) ¼ x 1 ¼” bolts, four (4) steel washers and two (2) locknuts. You may tighten the shooting rail assembly now.

STEP 11: Install the shooting rest assembly onto the two (2) remaining holes on the arm rests. NOTE: These holes should be toward 

the back of the treestand. Install using two (2) ¼ x 1 ½” bolts, four (4) steel washers and four (4) nylon washers as shown in 

Figure 26. NOTE: The shooting rail assembly mounts on the INSIDE of the armrests.

STEP 12: Locate the top ladder section. Install the top ladder section onto the top ladder section brackets using two (2) 1/4” x 1 

½” bolts, two (2) locknuts and four (4) steel washers as shown in Figure 27.

STEP 13: Locate the top ladder rung. Install it onto the top ladder section, on the inside, using two (2) 1/4 x 2 1/4” bolts, four (4) 

washers and two (2) locknuts as shown in Figure 28.

STEP 14: NOTE: The following assembly STEPS may be easier with the standing platform assembly on its side. Locate the two (2) 

diagonal braces. Install these onto the standing platform holes located in the center of the platform and the top ladder section 

using four (4) 1/4 x 2 1/2” bolts, eight (8) steel washer and four (4) locknuts as shown in Figure 29. NOTE: The upper end of the 

diagonal brace goes INSIDE the standing platform. The lower portion of the diagonal brace installs on the OUTSIDE of the upper 

ladder section.

STEP 15: With the treestand laying on the ground and on its side, you may now install the remaining ladder sections. NOTE: The 

ladder sections install using two (2) spring pins per section. Locate the middle ladder section. Slide the male end of the 

middle ladder section into the 

female

 end of the top ladder section as shown in Figure 30. Secure using spring pins as shown in 

Figure 31. Repeat this STEP for the lower ladder section installation

.

Figure 28

Install Top Ladder Rung

Onto Top Ladder Section

Figure 29

Install Diagonal Braces Onto Standing Platform 

and Top Ladder Section

Figure 30

Slide Ladder Section Together

Figure 31

Secure Ladder Section Using Spring Pins

Figure 32

Spring Pins Must Be Positively Engaged

Figure 33

Assemble Tree Stand Off

Summary of Contents for TNT REIGN SC 18LS























Reviews: