![Troy Built Models 50cc SPITFIRE Instruction Manual Download Page 5](http://html1.mh-extra.com/html/troy-built-models/50cc-spitfire/50cc-spitfire_instruction-manual_1172553005.webp)
6
6
Clevis
Copper joiner
6
6
Screw (2x10mm)
Nut (2mm )
6
Washer(2x5mm)
Clevis
1
Rod (2x300mm)
1
1
Retainer
1
Ring
1
1
Air tank
Switch
Washer(3x15mm)
Screw (3x80mm)
Lock Nut (3mm )
Clevis
Aluminum tube
Steel wire
2
Steel wire (0.5x3000mm)
2
2
2
Clevis
Washer(3x15mm)
Lock Nut (3mm )
1
Screw (3x80mm)
2
Copper joiner
The sketch map after the rudder shaft assemble finished.
2
Steel wire (0.5x3000mm)
3mm
30mm
Drill a hole to appropriate position in the
rudder as illustration.
Collar
Tail landing gear
TP Screw (2.3x8mm)
1.5mm
8
TP Screw (2.3x8mm)
Ply (15x15x3mm)
8
4
4
Clevis
Copper joiner
4
4
Screw (2x10mm)
Nut (2mm )
4
Washer(2x5mm)
Install the servo.
The servos installation finished sketch map.
Rudder servo
35mm
95mm
2
Plastical tube(3x30mm)
Drill a small hole to appropriate possition in the
fuselage for installing the plastical tube.
3mm
Steel wire
Copper joiner
Lock Nut (2mm )
Screw (2x10mm)
Ball joint
Washer(2x5mm)
Aluminum tube
Rudder servo
Rudder servo
Rudder servo
Rudder servo
Epoxy plies to appropriate position in the fuselage and
assemble the tail gear cover with screw.Then assemble
the wheel as illustration.
Connect the servo of rudder and the shaft for rudder
with steel wire as illustration.
50
51
53
54
10
49
52
Accessory list for the coming installation steps.
Install the nylon control horn and connect the linkage.
4mm
TP Screw (2.3x12mm)
8
TP Screw (2.3x12mm)
1.5mm
Secure the servo.Install the nylon control horn
and connect the linkage.
1
Main wing joiner(25x630mm)
1
Main wing joiner(20x570mm)
Rod (2.5x300mm)
Clevis
Clevis
Lock Nut (4mm )
Screw (3x10mm)
Nut (3mm )
Screw (4x35mm)
Washer
Washer(4x14mm)
Blind Nut (4mm)
Screw (4x40mm)
Gear door
Wheel (115mm)
TP Screw (3x20mm)
Washer (3x6mm)
PVC part
Retracts strut
LockNut(4mm)
Wooden Block
Note:rubber wheels oleo struts
and retracts are optional.
5mm
Rib template (3mm ply)
2
4
1
2
8
2
8
Washer (4x12mm)
4
2
1
1
Wood dowel (6x50mm)
LockNut(4mm)
Screw (4x75mm)
2
Wheel (115mm)
4
Wooden Block
2
Bushing (8X4mm)
Bushing (8X4mm)
C"
C = C"
C
side wing
centre wing
Rod (2.5x300mm)
Washer
Lock Nut (4mm )
Clevis
Clevis
Nut (3mm )
Collar (3mm)
Screw (3x10mm)
Screw (4x40mm)
2
2
Screw (4x40mm)
2
Washer
Lock Nut (4mm )
2
Clevis
2
Clevis
2
2
Screw (3x10mm)
Nut (3mm )
2
Collar (3mm)
2
Rod (2.5x300mm)
Washer(4x14mm)
2
Washer(4x14mm)
Reinforcement Plate (25x2mm)
4
Mount the gear door and the wheel to the retract.
Be care to notice the difference between
the left and the right wheel well.
Cut away the surplus parts of plastic cover
carefully along the shaded line.
The sketch maps when the retract up and down.
Trim the relevant position flat when assemble
the linkage of the servo tray.
12
13
11
15
3
14
Accessory list for the coming installation steps.