25
ARRANQUE Y PARADA
INSTRUCCIONES DE ARRANQUE
1. Mezcle la gasolina con el aceite. Consulte las
Instrucciones para
mezclar el aceite y el combustible
.
2. Llene el tanque de combustible. Consulte
Abastecer de
combustible la unidad
.
NOTA:
No hay necesidad de encender la unidad. El interruptor de
Encendido/Apagado debe estar en la posición ENCENDIDO ( I )
en todo momento (Fig. 6).
3. Oprima y suelte despacio la pera del cebador
10 veces
(Fig. 7).
Si no se ve combustible en la pera del cebador, oprima y suelte
la pera hasta que se vea el combustible.
4. Mueva el control de crucero a la posición LENTO (Fig. 6).
NOTA:
Mantenga el control de crucero en posición LENTO y
NO
presione el control del acelerador hasta el paso 9 (Fig. 6).
5. Levante la palanca del estrangulador hacia la derecha hasta que
haga clic (Fig. 7).
6. Agáchese en la posición de arranque (Fig. 8).
7.
NO
apriete el control del acelerador (Fig. 6). Tire de la cuerda de
arranque con un movimiento controlado y firme hasta que
arranque la unidad.
8. Ponga el motor en una marcha lenta durante 5 a 10 segundos.
Si la unidad se detiene durante ese período, oprima y mantenga
oprimido el control del acelerador o mueva el control de crucero
a la posición FAST (rápido) (Fig. 6) y tire de la cuerda de
arranque con un movimiento controlado y firme hasta que la
unidad se ponga en marcha.
9. Apriete y mantenga oprimido el control del acelerador o mueva
el control de crucero a la posición FAST (Fig. 6). Deje que el
motor se caliente durante 30 a 60 segundos.
NOTA:
Cuando el motor acelera sin fallar, la unidad ya se calentó
como es debido.
NOTA:
Cuando el motor se ha calentado correctamente, el control
de velocidad puede ajustarse y el control del regulador se puede
usar normalmente.
SI...
el motor no arranca, comience el procedimiento de arranque
por el paso 3.
SI...
la unidad está caliente o no arranca a los 3 tirones de la cuerda
de arranque, apriete y mantenga oprimido el control del
acelerador o mueva el control de crucero a la posición FAST,
luego tire de la cuerda de arranque con un movimiento
controlado y firme hasta que arranque la unidad.
INSTRUCCIONES DE APAGADO
1. Suelte el control del regulador, o mueva el control de velocidad a
la posición SLOW, y deje que el motor funcione en ralentí.
2. Oprima y no suelte el interruptor de control de Encendido y
Apagado en la posición APAGADO (O) hasta que el motor se
detenga por completo (Fig. 6).
ADVERTENCIA:
Cuando arranque la unidad,
asegúrese que no esté orientada hacia las personas,
animales, ventanas, automóviles o desechos sueltos.
ADVERTENCIA:
Opere esta unidad solamente en un
área exterior bien ventilada. El monóxido de carbono de
los gases de escape puede ser letal en un área confinada.
ADVERTENCIA:
Evite arrancar la unidad por
accidente. A fin de evitar lesiones graves, el operador y la
unidad deben estar en una posición estable al tirar de la
cuerda de arranque (Fig. 8).
Fig. 6
Fig. 8
Encendido ( I ) / Arranque
Apagado (O) / Parada
Control del
regulador
Posición de
arranque
Agarre de la cuerda
de arranque
Fig. 7
Bulbo del
cebador
Palanca del
cebador
Control de
velocidad
SLOW
(LENTA)
FAST (RÁPIDA)