background image

4

equipment. move machine to another area. Wait 5 
minutes before starting the engine.

i.

Never store the machine or fuel container inside 
where there is an open flame, spark or pilot light 
as on a water heater, space heater, furnace, 
clothes dryer or other gas appliances.

j.

Allow machine to cool 5 minutes before storing. 

Operation

1.

Before starting this machine, review the “Safety 
Instructions”. Failure to follow these rules may result in 
serious injury to the operator or bystanders. 

2.

Never leave this machine unattended with the engine 
running.

3.

Do not operate machine while under the influence of 
alcohol, drugs, or medication.

4.

Never allow anyone to operate this machine without 
proper instruction.

5.

Always operate this machine with all safety equipment in 
place and working. Make sure all controls are properly 
adjusted for safe operation.

6.

Do not change the engine governor settings or 
overspeed the engine. The governor controls the 
maximum safe operating speed of the engine.

7.

When loading a log, always place your hands on the 
sides of the log, not on the ends, and never use your foot 
to help stabilize a log. Failure to do so, may result in 
crushed or amputated fingers, toes, hand, or foot.

8.

Use only your hand to operate the controls.

9.

Never attempt to split more than one log at a time unless 
the ram has fully extended and a second log is needed to 
complete the separation of the first log.

10. For logs which are not cut square, the least square end 

and the longest portion of the log should be placed 
toward the beam and wedge, and the square end placed 
toward the end plate.

11. When splitting in the vertical position, stabilize the log 

before moving the control. Split as follows:

a.

Place log on the end plate and turn until it leans 
against the beam and is stable.

b.

When splitting extra large or uneven logs, the log 
must be stabilized with wooden shims or split 
wood between the log and end plate or ground.

12.  Always keep fingers away from any cracks that open in 

the log while splitting. They can quickly close and pinch 
or amputate your fingers.

13. Keep your work area clean. Immediately remove split 

wood around the machine so you do not stumble over it.

14. Never move this machine while the engine is running.
15. This machine should not be towed on any street, highway 

or public road without checking the existing federal, state, 
or local vehicle requirements. Any licensing or 
modifications such as taillights, etc., needed to comply, is 
the sole responsibility of the purchaser. If a “Statement of 
Origin” is required in your state, see your local dealer.

16. Do not tow machine faster than 45mph.
17. See Transporting the Log Splitter section in this manual 

for proper towing instructions once all federal, local, or 
state requirements are met. 

Maintenance and Storage

1.

Stop the engine, disconnect the spark plug and ground it 
against the engine before cleaning, or inspecting the 
machine.

2.

Stop the engine and relieve hydraulic system pressure 
before repairing or adjusting fittings, hoses, tubing, or 
other system components.

3.

To prevent fires, clean debris and chaff from the engine 
and muffler areas. If the engine is equipped with a spark 
arrester muffler, clean and inspect it regularly according 
to manufacturers instructions. Replace if damaged.

4.

Periodically check that all nuts and bolts, hose clamps, 
and hydraulic fittings are tight to be sure equipment is in 
safe working condition.

5.

Check all safety guards and shields to be sure they are in 
the proper position. Never operate with safety guards, 
shields, or other protective features removed.

6.

The pressure relief valve is preset at the factory. Do not 
adjust the valve.

7.

Never attempt to move this machine over hilly or uneven 
terrain without a tow vehicle or adequate help.

8.

For your safety, replace all damaged or worn parts 
immediately with original equipment manufacturer’s 
(O.E.M.) parts only. “Use of parts which do not meet the 
original equipment specifications may lead to improper 
performance and compromise safety!”

9.

Do not alter this machine in any manner, alterations such 
as attaching a rope or extension to the control lever, or 
adding to the width or height of the wedge may result in 
personal injury.

Your Responsibility

Restrict the use of this power machine to persons who read, 
understand and follow the warnings and instructions in this 
manual and on the machine. Some of the safety labels are 
reproduced here. Always follow directions on safety labels 
found on your equipment.

Summary of Contents for LS275

















Reviews: