background image

Section 4: Operation    

13

Stopping the Engine and Tiller
1. 

To stop the wheels and tines, release

the Forward Clutch Bail (all models) or the
Reverse Clutch Control (Models 634F and
634B) – whichever control is in use.

2.  

To stop the engine, put the ignition

switch and/or the throttle control lever in
the “OFF” or “STOP” position.

OPERATING THE TILLER

The following operating instructions pro-
vide guidelines to using your tiller effec-
tively and safely.  Be sure to read 

Tilling

Tips & Techniques  

in this Section before

actually putting the tines into the soil.

NOTE: This is a traditional “Standard-
Rotating-Tine” (SRT) tiller with forward
rotating tines.  It operates completely dif-
ferently from “Counter-Rotating-Tine”
(CRT) tillers or from front-tine tillers.

1.  

Follow the 

Pre-Start Checklist

at the

beginning of this Section.  Be sure that the
wheels are in the WHEEL DRIVE position.

2.  

Move the Depth Regulator Lever all the

way down, so that the tines clear the
ground.  Use this position when practicing
with the tiller and when traveling between
tilling sites.  Before actually tilling, move
the lever to the desired depth setting (see

Tilling Tips & Techniques

).

3.  

Start engine and allow it to warm up.

Then put throttle in “FAST” setting.

4.  

For 

forward

motion of the wheels and

tines:
(a) Pull Forward Clutch Bail (Fig. 4-1) up

against handlebar.  Release bail to stop
forward motion of wheels and tines.

(b) When tilling, relax and let the wheels

pull the unit while the tines dig.  Walk
behind and a little to one side of the
unit.  Use one hand, yet keep a light—
but secure—grip on the handlebar
(while keeping your arm loose).  See
Fig. 4-2.  Let the unit move at its own
pace and do not push down on the
handlebars to try and force the tines to
dig deeper — this takes weight off the
wheels, reduces traction, and causes
the tines to try and propel the tiller.

5.  

For 

reverse

motion of the wheels and

tines (Models 634F/634B only):
(a) Look behind and exercise caution when

operating in reverse.  

Do not till while

in reverse.

(b) Stop all forward motion.  Lift handlebar

with one hand until tines are off the
ground and then pull Reverse Clutch
Control knob out (see Fig. 4-3). To
stop reversing, let go of Reverse Clutch
Control knob.

6.

To move the Model 630B in reverse for

short distances:
(a) Release Forward Clutch Bail.  Then lift

handlebar until tines are off the ground.

(b) Swing the handlebar to the left so the

right wheel takes a “step” backward.
Next swing the handlebar to the right
so the left wheel “steps” backward.
Repeat as needed.

(c) If longer distances need to be covered

in reverse, shut off the engine, then
place the two wheels in FREEWHEEL.

7.  

To Turn the Tiller Around:

(a) Practice turning the tiller in a level,

open area.  Be very careful to keep
your feet and legs away from the tines.

(b) To begin a turn, lift the handlebars until

the tines are out of the ground and the
engine and tines are balanced over the
wheels (Fig. 4-4). 

(c) With tiller balanced, push sideways on

handlebar to steer in direction of turn
(Fig. 4-5).  After turning, slowly lower
tines into soil to resume tilling.

Stopping the Tiller and Engine
1.  

To stop the wheels and tines, release

the Forward Clutch Bail (all models) or the
Reverse Clutch Control (Models 634F and
634B) – whichever control is in use.

2.  

To stop the engine, put the ignition

switch and/or the throttle control lever in
the “OFF” or “STOP” position.

Keep away from rotating tines. Rotating

tines will cause injury.

WARNING

Fig. 4-2:  Use one hand to guide tiller when
moving forward.

Do not push down on the handlebars to
try to make the tiller till more deeply.
This prevents the wheels from holding
the tiller back and can allow the tines
to rapidly propel the tiller forward,
which could result in loss of control,
property damage, or personal injury.

WARNING

Fig. 4-3:  Raise tines off ground and look
behind when moving in reverse.

Fig. 4-4:  To begin turn, lift handlebars until
tines are out of ground and unit is balanced.

Fig. 4-5:  With tines out of ground, push
handlebars sideways to turn tiller.

Summary of Contents for 630B-Tuffy, 634F-Bronco, 634B-

































Reviews: