![background image](http://html.mh-extra.com/html/troy-bilt/500-series/500-series_operators-manual_1173249009.webp)
9
IMPORTANT:
Always release the drive control before
changing speeds.
Auger Control
The auger control is located on the left
handle. Squeeze the auger control to
engage the augers. Release to stop the
snow throwing action. The drive control
must also be released in order to stop
the auger.
IMPORTANT:
Refer to Auger Control Test on page 7 to
adjust the auger control. Read and follow all
instructions carefully and perform all adjustments to
verify your snow thrower is operating safely and
properly.
Ignition Key
The ignition key must be fully inserted in the switch
before the unit will start. Remove key when snow
thrower is not in use. Do not attempt to turn the key.
Discharge Chute
The angle of the discharge chute controls the distance
that the snow is thrown. Tilt the discharge chute up for
greater distance; tilt down for less distance.
Four Way Chute Control
This four-way control lever is meant to
control the direction and distance of
snow discharge from the chute. Press
the button on the knob and pivot it left
or right to rotate the chute to the
direction
that snow will be thrown. Tilt
the lever forward or rearward to adjust
the
distance
snow will be thrown.
Shift Lever
The shift lever is located in the center
of the handle panel and is used to
determine ground speed and direction
of travel. It can be moved into any of
eight positions.
IMPORTANT:
Always release traction control before
changing speeds.
Forward: The snow thrower has six forward (F)
speeds. Position one (1) is the slowest and position six
(6) is the fastest.
Reverse: The snow thrower has two reverse (R)
speeds—R1 is the slower of the two.
Headlight
The headlight is on whenever the engine is running.
Chute Clean-Out Tool
The chute clean-out tool is designed to clear a clogged
discharge chute. Refer to page
12
for instructions on
how to properly use it.
Wheel Steering Controls
The left and right wheel steering
controls are located on the underside
of the handles. Squeeze the right
control to turn right; squeeze the left control to turn left.
NOTE:
Operate the snow thrower in open areas until
you are familiar with these controls.
Skid Shoe
The skid shoe position is determined by the condition of
the ground from where snow has to be removed. Higher
the snow level, lower will be the skid shoe level. Adjust
it accordingly.
Stopping Snow Thrower
1.
To stop the wheels, release the traction drive lever
of the snow thrower.
2.
To stop throwing snow, release the auger drive lever.
3.
To stop the engine, push throttle control lever to
OFF and pull out the ignition key. Do not turn key.
Before Starting
WARNING:
Read, understand, and follow
all instructions and warnings on the machine
and in this manual before operating.
Gas & Oil Fill-Up
Service the engine with gasoline and oil as instructed in
the separate engine manual packed with your snow
thrower. Read instructions carefully.
WARNING:
Use extreme care when
handling gasoline. Gasoline is extremely
flammable and the vapors are explosive.
Never fuel the machine indoors or while the
engine is hot or running. Extinguish cigarettes,
cigars, pipes and other sources of ignition.
Starting The Engine
•
Attach spark plug wire to spark plug. Make certain
the metal loop on the end of the spark plug wire
6
1
2
F
3
4
5
R2
R1
R
WARNING:
Never use your hand to clear a
clogged discharge chute. Shut off engine and
remain behind handles until all moving parts
have stopped before unclogging.
WARNING:
Be sure no one other than the
operator is standing near the snow thrower
while starting or operating. Do not operate this
snow thrower unless the discharge chute
assembly has been properly installed and is
secured.
Summary of Contents for 500 series
Page 23: ...23 NOTES ...
Page 27: ...27 NOTES ...