Troy-Bilt 21A-630B063 Service Manual Download Page 9

Page: 9 / 42

Troy-Bilt Small Frame Tillers

DRIVE BELT REPLACEMENT:

4.1.

Remove the spark plug boot from the spark plug
and ground it to the engine. See Figure 4.1.

4.2.

Remove the hex flange screw and large flat
washer securing the belt cover to the lower
cable mounting bracket using a 3/8” socket. See
Figure 4.2.

4.3.

Pivot the belt cover on the forward clutch cable
until it is out of the work area.

Figure 4.1

Spark Plug Boot

Grounded

Spark
Plug

Figure 4.2

Hex Flange Screw

Large Flat Washer

Belt Cover

Clutch Cable

4.4.

Remove the belt from the engine drive pulley
and forward idler pulley. See Figure 4.4.

4.5.

Remove the belt from the transmission pulley.
See Figure 4.5.

4.6.

Install the new belt in the reverse order above.

NOTE:

Make certain the belt keepers are cor-

rectly positioned prior to installing the belt cover.

4.7.

Perform the Forward Clutch Cable Adjustment
section.

Figure 4.4

Drive Belt

Drive Pulley

Forward Idler Pulley

Figure 4.5

Transmission

Pulley

Belt

Summary of Contents for 21A-630B063











































Search results

Summary of Contents for 21A-630B063

Reviews:

Related manuals for 21A-630B063

Brands by name

Popular brands

Troy-Bilt 21A-630B063, Service Manual

Search results

Summary of Contents for 21A-630B063

Reviews:

Related manuals for 21A-630B063

Brands by name

Popular brands