background image

Servicing the Troy-Bilt Wide Cut 33” Combination Mower

 7

6.4.

Using a socket remove the Sems nuts and flat 
head screws securing the brake pad to the idler 
arm and remove the old brake pad. See Figure 
21.

6.5.

Loosely install the new brake pad. 

6.6.

Release the operator presence control and allow 
the new brake pad to engage the sheave of the 
idler pulley. See Figure 22. 

6.7.

Tighten the Sems nut to secure the brake pad to 
the idler arm.

7.

WHEEL DRIVE BELT REMOVAL AND 
REPLACEMENT.

NOTE: 

Some older units may not have all the 

belt guides installed.

7.1.

Release all mower controls.

Figure 21

Brake Pad

Sems Nuts

Figure 22

Brake pad seats into sheave

7.2.

Using a ½ inch socket, remove the two screws 
attaching the flap bracket to the frame. Remove 
the flap bracket. See Figure 23.

7.3.

Using a ½ inch socket remove the four screws 
securing the belt cover and remove the cover.

7.4.

Temporarily remove the blade drive belt from 
around the engine pulley.

7.5.

Use a  9/16 inch socket to loosen the locknut 
securing the pulley and belt guide to the front 
idler bracket. Remove the belt guide and pulley. 
See Figure 24.

NOTE: 

Maintain correct order of parts:

         - Pulley

         - Washer

         - Belt Guide

         - Nut

Figure 23

Flap Bracket

Screws

Figure 24

Front Idler Bracket Pulley

Engine Pulley

Trans. Pulley

Backside Idler Pulley

Trans. Pulley Belt Guide Cap Screw

Summary of Contents for 12A-E753B063























Reviews: