background image

7

EN

Operating manual – dehumidifier TTK 30 E

Dehumidification

The device keeps running until reaching the preselected relative
room humidity. Then the compressor switches off and the fan
keeps running. Once the preselected relative room humidity is
exceeded, the compressor switches back on.
The relative room humidity can be set within a setting range
from 30 % to 80 % in steps of 5 %. Additionally, the 

CO

 setting

for permanent dehumidification (continuous operation) can be
selected.
You can choose between low and high fan speed.

1. Press the 

MODE

 button (14).

ð

The indication of the currently selected operating mode
flashes.

2. Press the arrow buttons (18, 19) until the LED for

dehumidification

 mode (13) starts flashing.

3. Then press the 

MODE

 button (14) again.

ð

Dehumidification

 mode is selected.

4. Press the arrow buttons (18, 19) to adjust the relative room

humidity or to select continuous operation (

CO

).

5. Press the 

FAN

 button (17) to select either low or high fan

speed.

ð

The selected fan speed is indicated on the 

fan speed

indication (21).

Automatic operation

The relative room humidity is preset to 55 % and cannot be
changed.
If the relative room humidity lies between 55 % and 70 %, the
fan automatically switches over to low speed.
Below a relative room humidity of 55 %, the compressor
switches off.
Above a relative room humidity of 70 %, the fan runs at the
highest level.

Info

In automatic mode, the 

fan speed

 indication (21) does

not change automatically.

1. Press the 

MODE

 button (14).

ð

The indication of the currently selected operating mode
flashes.

2. Press the arrow buttons (18, 19) until the LED for

automatic

 mode (13) starts flashing.

3. Then press the 

MODE

 button (14) again.

ð

Automatic

 mode is selected.

Continuous operation

The device dehumidifies the air constantly and regardless of the
relative room humidity.
The relative room humidity and the fan speed cannot be set in
this operating mode.

1. Press the 

MODE

 button (14).

ð

The indication of the currently selected operating mode
flashes.

2. Press the arrow buttons (18, 19) until the LED for

continuous operation

 (13) starts flashing.

3. Then press the 

MODE

 button (14) again.

ð

Continuous operation

 is selected.

Laundry drying function

The device may be used to dry clothes in a more timely manner.
When positioning the device or a clothes horse, please observe
the minimum distances specified in the technical data.
The device dehumidifies the air constantly and regardless of the
relative room humidity. The fan runs at the highest speed.
The relative room humidity and the fan speed cannot be set in
this operating mode.

1. Press the 

MODE

 button (14).

ð

The indication of the currently selected operating mode
flashes.

2. Press the arrow buttons (18, 19) until the LED for the

laundry drying function

 (13) starts flashing.

3. Then press the 

MODE

 button (14) again.

ð

The 

laundry drying function

 is selected.

Ventilation

In 

ventilation

 mode you can choose between low and high fan

speed.

1. Press the 

MODE

 button (14).

ð

The indication of the currently selected operating mode
flashes.

2. Press the arrow buttons (18, 19) until the LED for

ventilation

 mode (13) starts flashing.

3. Then press the 

MODE

 button (14) again.

ð

Ventilation

 mode is selected.

4. Press the 

FAN

 button (17) to select either low or high fan

speed.

ð

The selected fan speed is indicated on the 

fan speed

indication (21).

Summary of Contents for TTK 30 E



















Reviews: