background image

EN

2

Operating manual – gas heater fan TGH 10 E / TGH 15 E / TGH 30 E

Safety

Read this manual carefully before starting or using the
device. Always store the manual in the immediate vicinity
of the device or its site of use!

Warning
Read all safety warnings and all instructions. 

Failure to follow the warnings and instructions may
result in electric shock, fire and / or serious injury.

Save all warnings and instructions for future
reference. 

This appliance can be used by children aged from 
8 years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and
user maintenance shall not be made by children
without supervision.

Do not use the device in potentially explosive rooms.

Do not use the device in aggressive atmosphere.

Set the device up in an upright and stable position.

Let the device dry out after a wet clean. Do not operate it
when wet.

Do not use the device with wet or damp hands.

Do not expose the device to directly squirting water.

Never insert any objects or limbs into the device.

Do not cover or transport the device during operation.

Do not sit on the device.

This appliance is not a toy! Keep away from children and
animals. Do not leave the device unattended during
operation.

Check accessories and connection parts for possible
damage prior to every use of the device. Do not use any
defective devices or device parts.

Ensure that all electric cables outside of the device are
protected from damage (e.g. caused by animals). Never
use the device if electric cables or the power connection
are damaged!

The electrical connection must correspond to the
specifications in chapter Technical data.

Insert the mains plug into a properly secured mains
socket.

Observe the device's power input, cable length and
intended use when selecting extensions to the power
cable. Completely unroll extension cables. Avoid electrical
overload.

Before carrying out maintenance, care or repair work on
the device, remove the mains plug from the mains socket.
Hold onto the mains plug while doing so.

Switch the device off and disconnect the power cable from
the mains socket when the device is not in use.

Do not under any circumstances use the device if you
detect damages on the mains plug or power cable. 
If the supply cord is damaged, it must be replaced by the
manufacturer, his service agent or similarly qualified
persons in order to avoid a hazard.
Defective power cables pose a serious health risk.

Observe the storage and operating conditions (see chapter
Technical data).

Ensure a minimum distance of 3 m to combustible
substances. Do not use the device in rooms where fuel,
solvents, varnishes or other easily inflammable vapours
are stored.

Ensure that the air inlet and outlet are not obstructed.

Do not place the device on combustible ground.

Allow the device to cool down before transport and / or
maintenance work.

Protect the device from moisture, e.g. rain.

Protect the gas cylinder from sub-zero temperatures also
known as frost.

Carefully inspect all connection points for tightness.
Attention! Leak testing by way of naked flame is strictly
forbidden!

The exchange of gas cylinders is only permitted in an
environment devoid of ignition sources.

In case of gas leakage (smell) immediately close the gas
cylinder's main valve and keep the device at a distance to
any fire source.

Never turn the gas cylinder over, even though it may seem
empty! This could cause an obstruction in the hose with
the remains from the gas cylinder and so lead to a fire
hazard and immediate damage of the device.

Do not twist the gas hose.

Do not dismantle the protective grid and / or other device
components.

Do not position the gas cylinder in front of the device. Risk
of fire and explosion!

Only use the original gas hose and original spare parts.

Keep fire extinguisher and first-aid kit on hand.

Bear in mind, that you may have to meet different national
requirements. Observe the local regulations regarding
admissible deviations. In Germany consult the Technical
Rules for Liquid Gas (TRF 2012) as well as the relevant
accident prevention regulations (VBG and ZH 1/455).

Summary of Contents for TGH 10 E


















Reviews: