Trotec PTNS 10-230V Operating Manual Download Page 5

EN

4

Operating manual – tacker PTNS 10-230V

Intended use

Only use the device 

PTNS 10-230V

 for tacking cardboard,

leather, insulating material, fabrics made of textile or natural
fibres, foils and similar materials onto a soft ground such as
softwood or material similar to wood whilst adhering to the
technical data.
We recommend using the power tool with original Trotec
accessories.

Improper use

The device 

PTNS 10-230V

 is not suitable for tacking hard

materials such as metals, stone materials, glass and hard
plastics.

Personnel qualifications

People who use this device must:

have read and understood the operating manual, especially
the Safety chapter.

Personal protective equipment

Wear hearing protection.

Excessive noise can lead to hearing loss.

Wear eye protection. 

With it you protect your eyes from splintering, falling
and flying pieces which could cause injuries.

Wearing protective gloves.

They protect your hands from burns, crushing injuries
and skin abrasions.

Residual risks

Warning of electrical voltage

Electric shock from insufficient insulation.
Check the device for damages and proper functioning
before each use.
If you notice damages, no longer use the device.
Do not use the device when the device or your hands
are damp or wet!

Warning of electrical voltage

Work on the electrical components must only be
carried out by an authorised specialist company!

Warning of electrical voltage

Before any work on the device, remove the mains plug
from the mains socket!
Hold onto the mains plug while pulling the power cable
out of the mains socket.

Warning of electrical voltage

There is a risk of a short-circuit due to liquids
penetrating the housing!
Do not immerse the device and the accessories in
water. Make sure that no water or other liquids can
enter the housing.

Warning

Do not process materials containing asbestos.
Asbestos is considered carcinogenic.

Warning

Make sure not to hit power, gas or water lines when
working with a power tool.
If necessary, use a pipe detector to check the wall you
want to drill in or slit open.

Warning

Risk of injuries caused by flying parts or bursting tool
heads.

Warning

Dangers can occur at the device when it is used by
untrained people in an unprofessional or improper way!
Observe the personnel qualifications!

Warning

The device is not a toy and does not belong in the
hands of children.

Warning

Risk of suffocation!
Do not leave the packaging lying around. Children may
use it as a dangerous toy.

Caution

Vibration emissions can cause a health hazard if the
device is used for an extended period of time or if it is
not properly handled and maintained.

Caution

Keep a sufficient distance from heat sources.

Notice

If you store or transport the device improperly, the
device may be damaged.
Note the information regarding transport and storage of
the device.

Behaviour in the event of an emergency

1. Disconnect the device from the mains feed-in: 

Hold onto the mains plug while pulling the power cable out
of the mains socket.

Summary of Contents for PTNS 10-230V













Reviews: