Tropos Networks 7320 Outdoor Installation Manual Download Page 46

Page: 46 / 100

Chapter 1

Tropos 7320 Router Installation Guide

Figure 22

shows the layered shield and jacket for the data cable, which must be removed to

expose the inner cable and twisted pairs.

Figure 22

Data Cable Detail

Note

Attach ground and data cables to the router before sliding it into the sun shield.

Connect to the data port

Verify that power is turned off on the designated circuits.

Run shielded Category 5 Ethernet cable appropriate for outdoor use from a data protection
unit to the router.

Connect one end of the Category 5 cable to the protection unit.

Remove the connector access cover on the bottom of the router.

Run raw cables for the Management or LAN port, or both, through the bulk head openings,
allowing sufficient length to terminate the cables without causing crowding in the
connection area. See

Figure 23

trp_117

Watertight bulkhead

cable glands

Cable

Outer

jacket

Twisted

pairs

Securely tighten gland

for weathertight seal

Conductive

shield

Belfoil

shield

Terminate cable shield

at cable gland

1/2 inch

Connector access

cover

Summary of Contents for 7320





































































































Search results

Summary of Contents for 7320

Reviews:

Related manuals for 7320

Brands by name

Popular brands

Tropos Networks 7320, Outdoor Installation Manual

Search results

Summary of Contents for 7320

Reviews:

Related manuals for 7320

Brands by name

Popular brands