background image

25

Cleaning the Steel Mesh Filter 

x

  Please clean the steel mesh (or replace the filter) 

according to the local water quality. 

x

  When the cleaning strength becomes weaker, clean the 

steel mesh or replace the filter on time. Close the water 

supply angle valve when disassembling the filter. Tighten 

the filter during installation to avoid water leakage. 

x

 Turn 

the 

filter 

counterclockwise with a coin to open the 

filter. It is recommended to clean the steel mesh every 1-2 

months. 

Replacing the Battery 

x

  Loosen the screws that secure the battery cover, remove 

the old battery and give it to a professional recycling 

agency. 

x

  Replace the new battery and lock the fixing screw as 

shown in the picture. 

x

  Refer to the battery installation picture to install the 

battery properly. 

R

 

Note: Keep the battery out of reach of children. 

Please confirm the positive and negative of battery. Do 
not change, disassemble, or burn the battery. Don’t mix 
it with old batteries or different types of batteries to 
avoid leakage or explosion. 

R

 

Note: The battery case has a moisture-proof 

function. Please tighten the fixing screws to achieve a 
good sealing effect. 

 

 

 

 

 

Summary of Contents for Tahum TETBCERN-12.WH





























Reviews: