background image

Models:  02-1040C0111 & 02A1040C0111 

10 Ton (8.93 Metric Ton) Single Stage Jack 

 

12/2020 | Rev. 02 

Page | 5 

 
6.4.2 

Jack Instructions 

To Raise Aircraft: 

1.  Place jack on a hard, level surface. 
2.  Raise mechanical extension as close to aircraft jack pad as possible. 
 

WARNING! 

The locking pin MUST be placed in the ram protection ring groove and fully through the mechanical 
extension. 

 

The locking pin washer and ball lock MUST be placed outside the ram protection ring. 
 

 

Visually inspect the jack prior to every use. 

 

Do not place extra locking pins in any other hole on 
the mechanical extension. 

 

Insure mating surfaces to jack point are free of 
debris and damage. 

 

Under no conditions should the locking pin washer 
or washer groove be inside the ram protection ring 
groove. 

 

Under no conditions should the locking pin’s ball 
lock be inside the ram protection ring groove. 

 

Never use the jack if the ram protection ring is not 
installed. 

 

Never use the locking pin without a locking pin 
washer. 

 

Never use a locking pin that has been damaged. 

 

Never use a ram protection ring that has been 
damaged or deformed. 

 

Replace ram protection ring if it does not have a 
radius groove for the locking pin. 

 

Load test jacks annually. 

 

Only order replacement parts from Tronair. 

 

Failure to comply could result in premature failure 
below certified weight and could cause serious injury including death. 

 
 

Correct Pin Placement 

 

 

Summary of Contents for 02-1040C0111








































































Reviews: