TRITON Extreme
EasyStart
2.
Press the
SAMPLING
key
Ä
Press the “Input Setup” tab
Ä
Press the upper-right
▼
popup, and then
press the scroll bar to display “Auto Sampling Setup”
Ä
Press “REC Audio Input”, and then set “Source
Audio” to “Analog”, “Stereo” to “Mono-1”, “Save to” to “RAM” and “IFX” to “Off”
Ä
Press “OK”. All
sampling parameters will now be automatically set up.
3.
Now to change the “Trigger” setting, so that sampling will begin when the input audio exceeds the set
level: Press the “Trigger”
X
popup and set this to “Threshold”
Ä
Set the “Level” to “-30 dB”, and then
set “Pre-Trigger” to “005 ms”, in order to capture the very beginning of the sample when sampling
begins.
4.
Set the recording level with the
REAR PANEL LEVEL
knob – speak into the mic and adjust the level as
high as possible without allowing the “ADC OVERLOAD !!” warning to appear in the display
Ä
Press the
SAMPLING REC
key, and then adjust the “Recording Level” with the
VALUE SLIDER
– set this as high
as possible, avoiding the “CLIP!!” warning.
5.
With the
SAMPLING REC
key still lit, press the
SAMPLING START/STOP
key, and then speak into
the mic, saying the word “
This
”
Ä
When finished speaking, press the
SAMPLING START/STOP
key to
stop sampling. Press
C2
on the keyboard to hear your new sample.
6.
Now to make settings for individual samples across the keyboard (multisample): Press the “Preference”
tab and set the “Zone Range” to “1 key”
Ä
Un-check the “Auto Loop On” checkbox, and then press the
“Recording” tab
Ä
Set “OrigKey” and “TopKey” to “C2” - the easiest way to set this is by
holding down
the
ENTER
key and pressing the
C2
key on the keyboard
Ä
Press the “Create” button in the display to
set a new key index (“C#2”).
7.
Press the
SAMPLING
START/STOP
key and say the word,
“is”
Ä
Press
SAMPLING
START/STOP
again to stop sampling, and then press the “Create” button in the display
.
Note that the “keyboard”
display moves to the next key after you press “Create”.
8.
Repeat the previous step 3x, to record three more samples, sampling “
the
”, “
Triton
”, and finally
“
Extreme
” …That’s it! Now play the keyboard: play each note (half-step) from
C2
to
E2
, and you’ll
hear the sampled words,
“This is the TRITON Extreme“
.
Tip:
You can use the above procedure with any external audio source, such as a drum machine – to create a new
multisampled drum kit!
Continue by sampling through one of the Extreme’s Insert Effects…
9.
Press the “Input Setup” tab
Ä
In the “Input 1” field, press the
X
popup by “BUS(IFX) Select” and
choose “IFX1”
Ä
Set “Pan” to “C064” (use the
numeric keypad
and enter “64”, followed by pressing
the
ENTER
key).
10.
Press the
MENU
key, and
then press
“
P8: Insert Efffect”
Ä
Press the “Insert FX” tab, and press to set
the “OFF” toggle button in the “IFX1” box “ON”
Ä
Press to highlight “000:No Effect”, and select “052:
Reverb Hall” for IFX1
Ä
Speak into the microphone to hear the effect being applied.
11.
Press the
EXIT
key, then press the “Recording” tab
Ä
Press the
SAMPLING REC/WRITE
key
Ä
Speak
into the mic and adjust the recording level as needed.
12.
Press the
SAMPLING START/STOP
key, and then speak to sample
Ä
Press
SAMPLING
START/STOP
to stop sampling. The new sample will playback on key
F2
– the next available index
Ä
Press the
“Create” button to set a new key index.
Continue by sampling though the tube and using
Valve Force
technology…
13.
Press the
VALVEFORCE ON/OFF
key (it will light)
Ä
Press the
MENU
key, and then select “P9: VALVE
FORCE”
Ä
Use the
DIAL
to set “Placement” to “Insert (Use 3/4 BUS)”.
14.
Press the
EXIT
key, and then press the “Input Setup” tab
Ä
Set “Pan” to “C064” and “BUS” to “3
(Tube)”
Ä
Press the “Recording” tab.
15.
Press the
REALTIME CONTROL
key until the LED lights in the
VALVEFORCE
section, and as you speak
into the mic, work with the
CONTROL
knobs to set Valve Force parameters to suit.
8