manualshive.com logo in svg

Tritech Merlin, Product Manual

Share
Download
Tritech Merlin Product Manual Download Page 14

Merlin

0711-SOM-00001, Issue: 03

14

© Tritech International Ltd.

5. Maintenance

Warning

Do not power the pump or hydraulic valve actuators until all hoses are properly

connected to the pump.

There is a serious risk of injury to fingers if inserted into either the power water

intake or the pump delivery port.

If undertaking any testing operations suitable guards and other safety measures

must be in place.

5.1. Tools Required

The following tools are required to work on the pump:

• 22mm open ended spanner

• 13mm open ended spanner

• 18m ring spanner (for actuator stripdown)

• 10mm Allen key

• 8mm Allen key

• 6mm Allen key

• 5mm Allen key

• 2.5mm Allen key

• Dead blow hammer

• Loctite - "Studlock" for reassembly

For detailed assembly procedures refer to Appendix B, 

Merlin Assembly

.

5.2. Basic Procedures

Hydraulic Motor Shaft Seals

The pumps are fitted with either an 'H' (red) or 'V' (brown) type seal. The type V is the standard

seal and is high pressure, high temperature.

Replacement of seals with anything other than a genuine seal (or 

Tritech International Ltd

supplied seal) will invalidate the warranty.

Pre-dive

Visual check for external damage.

Summary of Contents for Merlin

































Reviews:

No comments

Brands by name

Popular brands

Load more brands